|
KEYWORD |
PART
NUMBER |
DESCRIPTION |
|
ADF Assembly |
Q3948-60189 |
Automatic document feeder (ADF) and
flatbed scanner lid - Includes the lid, the ADF feed mechanism, and
scanner 50-page input tray - Mounts on top of the scanner assembly |
| Q3948-60193 |
ADF assembly |
| Q3948-60118 |
ADF assembly |
|
Airflow Guide |
RB2-9904-000CN |
Airflow Guide (duct) - Black plastic
insert piece which runs the width of the printer and has an air flow
hole on right side - Directs air flow from the fan on the left side
of the printer to the fusing assembly - Snap locks in center rear of
printer |
| RB9-0901-000CN |
Airflow guide (duct) / fan holder
bracket assembly (Alloy Gray plastic) - Mounts on the left metal
side frame assembly |
| Q3948-67915 |
Airflow guide (duct) kit - Includes
the airflow guide / fan holder bracket assembly with high voltage
label - Mounts on the left metal side frame assembly |
|
Arm |
RB3-1083-000CN |
Face-down paper exit arm - Helps to
prevent paper re-entering the printer and paper curl - Mounts on the
right side of the top cover output tray |
| RB3-0089-030CN |
Top cover rack arm (Black) - Plastic
arm with teeth on bottom edge - Disengages the imaging drum/transfer
assembly drive cams when the top door is open - Mounts on the lower
right side of the cartridge access door |
|
Belt |
Q3948-67918 |
Feed belt kit - Includes one paper
feed guide drive (large) belt, two 3-belt pulley rollers, two 1-belt
pulley rollers, and eight paper feed (small) belts - Mounts just
behind the transfer roller in the middle frame assembly |
| RB1-8668-030CN |
Feed guide drive belt - Small belt
approximately 5/16 inch wide with 'A' shaped ribs on it - Between
the feed drive roller and the small center roller - Driven via the
transfer roller gear train |
| RB3-0063-000CN |
Paper feed belt - Small black rubber
belt approximately 1/8 inch wide with little 'A' shaped ribs on it -
Goes between the feed drive roller and the pulley rollers (eight
used) |
| Body |
RG5-7639-000CN |
250-sheet cassette tray main body
assembly - Includes the main structure frame, paper stops, lift
plate, springs, and the separation pad assembly - Does NOT include
the plastic front cover - For the cassette on the 250-sheet input
tray assembly |
|
Bushing |
RB3-1027-000CN |
Bushing - Flanged plastic bushing -
Mounts on the left end of the pressure roller in the fusing assembly |
| RB3-1094-000CN |
Bushing assembly (Black plastic
bushing with small guide roller on top) - Holds the right end of the
transfer roller assembly in the middle frame assmebly |
| RS5-1636-000CN |
Shaft bushing - Mounts on the gear
end of the feed roller shaft in the base on the 250-sheet input tray
assembly |
| RS5-1637-000CN |
Bushing (black plastic) - Mounts on
the right end of the registration roller assembly |
| RB2-3043-000CN |
Left roller bushing - Acts as the
bearing and retainer for the left end of the paper pickup roller
assembly (tray 1) - Mounts on the left side of the front frame
assembly |
| RB3-1026-000CN |
Bushing - Plastic 'U' shaped bushing
- Mounts on the right end of the pressure roller in the fusing
assembly |
| RB9-0835-000CN |
Shaft bushing/retainer - Left side
pickup roller support bushing - Mounts on and retains the left end
of the pickup roller shaft - For the base on the 250-sheet input
tray assembly |
| RS5-1638-000CN |
Bushing - For the registration
roller gear drive shaft on the right side of the front frame
assembly, and the left side of the feed roller in the 250-sheet
paper input tray assembly |
| RB2-3044-000CN |
Right roller bushing - Acts as the
bearing and retainer for the right end of the paper pickup roller
assembly (tray 1) - Mounts on the right side of the front frame
assembly |
| RB9-0879-000CN |
Bushing/shaft retainer assembly
(Black plastic) - Holds the rotation drive shaft in the right side
plate of the toner cartridge carousel (rotary) assembly |
| RB2-9809-000CN |
Bushing/shaft retainer assembly
(White plastic) - Holds the rotation drive shaft in the left side
plate of the toner cartridge carousel (rotary) assembly |
| RB9-0834-000CN |
Shaft bushing/retainer - Right side
pickup roller support bushing - Mounts on and retains the right end
of the pickup roller shaft - For the base on the 250-sheet input
tray assembly |
| RS5-1635-000CN |
Shaft bushing - For the paper pickup
clutch gear shaft - Mounts on the plate of the multipurpose paper
pickup gear assembly |
|
Cable |
RG5-7114-020CN |
CABLE, MOTOR |
| RG5-7128-000CN |
Cable assembly (four 3-pin
connectors) - Connects between the DC controller board (J107 and
J138) and the leading edge paper sensor for the fusing assembly
(J720) and the registration sensor (J711) |
| RG5-7154-000CN |
Fusing assembly cable (for 110VAC to
127VAC operation) - Connects the fusing heater assembly and the
paper sensor to the fusing assembly connector |
| RG5-7433-000CN |
Cable assembly - Connects between
the Interconnecting feed drive PC board and the printer connector -
Mounts in the right side support frame/cover assembly of the
250-sheet input tray assembly |
| RG5-7106-000CN |
Cable assembly (two 2-pin
connectors) - Connects between the low voltage power supply board
(J401) and the formatter board (J1003) |
| RG5-7155-000CN |
Fusing assembly cable (for 220VAC to
240VAC operation) - Connects the fusing heater assembly and the
paper sensor to the fusing assembly connector |
| RG5-7138-000CN |
Cable assembly - From sensor (PS717)
(which senses paper feeding from optional tray 3) to the small
interconnecting PC board on the right side frame/cover assembly -
For the base on the 250-sheet input tray assembly |
| RG5-7156-000CN |
Cable assembly (two 2-pin
connectors) - Connects between the low voltage power supply board
(J404) and the formatter board (J1004) |
| RG5-7161-000CN |
Cable assembly (two 3-pin connectors
and a spad lug) - Connects between the fusing assembly connector and
the low voltage power supply board (J302), and the chassis ground |
| RG5-7117-000CN |
Cable assembly (two 3-pin
connectors) - Connects between the engaging sensor (J712) on the
toner cartridge carousel and the DC controller board (J125) |
| RG5-7115-000CN |
Cable assembly (two 3-pin
connectors) - Connects between the roller engaging photosensor
(J714) and the DC controller board (J115) |
| RG5-7624-000CN |
Cable assembly (two 3-pin
connectors) - Connects between the waste toner sensor PC board (J61)
and the DC controller board (J108) |
| RG5-7114-000CN |
Cable assembly (two 4-pin
connectors) with shield - Connects between the cartridge drive motor
(J705) the DC controller board (J106) |
| RG5-7620-000CN |
Cable assembly (two 5-pin
connectors) - Connects between the DC controller board (J139) and
the fusing assembly drive motor (J702) |
| RG5-7126-000CN |
Cable assembly (two 5-pin
connectors) - Connects between the sub-high voltage board (J505) and
the high voltage board (J503) |
| RG5-7109-000CN |
Cable assembly (two 7-pin
connectors) - Connects between the DC controller board (J119) and
the fusing assembly connector (J201) |
| RG5-7621-000CN |
Cable assembly (two 8-pin
connectors) - Connects between the low voltage power supply board
(J402) and the DC controller board (J134) |
| RG5-7108-000CN |
Cable assembly (two 8-pin
connectors, Purple wire) - Connects between the low voltage power
supply board (J403) and the DC controller board (J133) |
| RG5-7129-000CN |
Cable assembly (two connectors and
two spade lugs) - From toner cartridge contacts on the left carousel
side plate to the cable (J512 and J511) that runs to the high
voltage power supply board |
| RG5-7122-000CN |
Cable assembly - 'Y' type cable
(three connectors) - The 14-pin connector splits into an 8-pin
connector and a 6-pin connector - Connects between the DC controller
board (J118) and the optional paper tray connectors (J230) |
| Q3948-60129 |
Flat flexible cable (FFC) assembly -
Connects between the camera (photo) interface board set and the
formatter board |
| Q3948-60144 |
Flat flexible cable (FFC) assembly -
Connects between the formatter assembly (J1001) and the DC
controller board (J101) |
| RH2-5524-000CN |
Flat flexible cable (FFC) assembly -
Connects between the laser/scanner assembly (J11) the DC controller
board (J102) |
| RG5-7145-000CN |
Front cable assembly (six
connectors) - From various components on the front frame assembly
and right side to the DC controller board |
| RG5-7123-000CN |
Grounding cable assembly - Connects
from the optional tray connector housing to the metal right side
frame assembly |
| RG5-7146-000CN |
High voltage cable assembly (two
15-pin connectors and two 14-pin connectors) - Connects between the
high voltage power supply board (J501 and J502) and the DC
controller board (J136 and J135) |
| RG5-7130-000CN |
High voltage cable assembly -
Connects between the high voltage board spring contacts (on the
middle frame assembly) and the cables for the toner cartridge
carousel left plate assembly (J511 and J512) |
| RG5-7160-000CN |
Upper cable assembly (seven
connectors) - Interconnects various upper level components to the DC
controller board |
|
Cable (Interface) |
8121-0712 |
Universal Serial Bus (USB) interface
cable (Black) - Type 'A' connector to type 'B' connector - 0.6m
(24-inches) long - USB 2.0 compliant |
| 8121-0868 |
Universal Serial Bus (USB) interface
cable (Black) - Type 'A' connector to type 'B' connector - 1.83m
(6.0ft) long |
| C6518A |
Universal Serial Bus (USB) interface
cable - Type 'A' connector to type 'B' connector - 2.0m (6.6ft) long |
| C6520A |
Universal Serial Bus (USB) interface
cable - Type 'A' connector to type 'B' connector - 3.0m (9.8ft) long |
| C2392A |
Universal serial bus (USB) interface
cable - Type 'A' connector to type 'B' connector - 5.0m (16ft) long |
|
Carousel |
RG5-7587-090CN |
Carousel (rotary) assembly -
Includes the carousel assembly, the support assembly, end plates,
drive gears and shaft, sensors, and cables |
| RG5-7587-000CN |
Carousel (rotary) assembly -
Includes the carousel assembly, the support assembly, end plates,
drive gears and shaft, sensors, and cables - Mounts towards the rear
of the printer in front of the rear frame assembly |
|
Cartridge |
Q3960A |
HP Color LaserJet smart Black print
cartridge - Will print approximately 5,000 pages based on a 5% print
density |
| Q3960-67902 |
HP Color LaserJet smart Black print
cartridge - Will print approximately 5,000 pages based on a 5% print
density (Europe) |
| Q3960-67901 |
HP Color LaserJet smart Black print
cartridge - Will print approximately 5,000 pages based on a 5% print
density (not for Europe) |
| Q3971-67901 |
HP Color LaserJet smart Cyan print
cartridge - Will print approximately 2,000 pages at based on a 5%
print density (not for Europe) |
| Q3971A |
HP Color LaserJet smart Cyan print
cartridge - Will print approximately 2,000 pages based on a 5% print
density |
| Q3971-67902 |
HP Color LaserJet smart Cyan print
cartridge - Will print approximately 2,000 pages based on a 5% print
density (Europe) |
| Q3961A |
HP Color LaserJet smart Cyan print
cartridge - Will print approximately 4,000 pages based on a 5% print
density |
| Q3961-67902 |
HP Color LaserJet smart Cyan print
cartridge - Will print approximately 4,000 pages based on a 5% print
density (Europe) |
| Q3961-67901 |
HP Color LaserJet smart Cyan print
cartridge - Will print approximately 4,000 pages based on a 5% print
density (not for Europe) |
| Q3973A |
HP Color LaserJet smart Magenta
print cartridge - Will print approximately 2,000 pages based on a 5%
print density |
| Q3973-67902 |
HP Color LaserJet smart Magenta
print cartridge - Will print approximately 2,000 pages based on a 5%
print density (Europe) |
| Q3973-67901 |
HP Color LaserJet smart Magenta
print cartridge - Will print approximately 2,000 pages based on a 5%
print density (not for Europe) |
| Q3963A |
HP Color LaserJet smart Magenta
print cartridge - Will print approximately 4,000 pages based on a 5%
print density |
| Q3963-67902 |
HP Color LaserJet smart Magenta
print cartridge - Will print approximately 4,000 pages based on a 5%
print density (Europe) |
| Q3963-67901 |
HP Color LaserJet smart Magenta
print cartridge - Will print approximately 4,000 pages based on a 5%
print density (not for Europe) |
| Q3972A |
HP Color LaserJet smart Yellow print
cartridge - Will print approximately 2,000 pages based on a 5% print
density |
| Q3972-67902 |
HP Color LaserJet smart Yellow print
cartridge - Will print approximately 2,000 pages based on a 5% print
density (Europe) |
| Q3972-67901 |
HP Color LaserJet smart Yellow print
cartridge - Will print approximately 2,000 pages based on a 5% print
density (not for Europe) |
| Q3962A |
HP Color LaserJet smart Yellow print
cartridge - Will print approximately 4,000 pages based on a 5% print
density |
| Q3962-67902 |
HP Color LaserJet smart Yellow print
cartridge - Will print approximately 4,000 pages based on a 5% print
density (Europe) |
| Q3962-67901 |
HP Color LaserJet smart Yellow print
cartridge - Will print approximately 4,000 pages based on a 5% print
density (not for Europe) |
| Clamp |
WT2-5700-000CN |
Cable clamp - White plastic clamp
with mounting pin - Mounts on the upper right side of the front
frame assembly, the lower left side of the middle frame assembly,
and the lower middle of the fusing assembly (three used) |
|
Clip |
WT2-5056-000CN |
Cable clip - 'C' shaped White
plastic - Mounts in the opening on the cover for the paper pickup
solenoid |
| WT2-5610-000CN |
Cable clip - White plastic push-in
clip with mounting pin - Mounts on the contact plate on the top
right side of the middle frame assembly |
| XD2-1100-502CN |
E-ring clip - Secures the dual gear
to the drive shaft which drives the registration roller - Located on
the inside of the front frame assembly |
| XD2-1100-322CN |
E-ring retainer clip - Used to
secure the electromagnetic clutch assembly (CL1) on the paper pickup
shaft |
|
Clutch |
RH7-5389-000CN |
Electromagnetic clutch assembly
(24V) - Electrical clutch between the clutch drive gear and shaft -
(CL1) Engages the registration roller assembly |
| RH7-5335-000CN |
Electromagnetic clutch assembly
(24VDC) - Electrical clutch between the clutch drive gear and shaft
- (CL2) Engages the roller within the imaging drum/transfer assembly
from the main gear train |
|
Connector |
WS1-6336-000CN |
Connector assembly - For optional
paper tray - Mounts to the bottom right side of the middle frame
assembly |
| WS1-6337-000CN |
Dual connector - Houses both a 8-pin
and 6-pin connector - Interconnects the printer with the 250-sheet
tray assembly - Mounts in the right side support frame/cover
assembly |
| WT2-5737-000CN |
Drawer connector - Connector located
on bottom of tray assembly frame on right side, which connects tray
assemblies to each other - Mounts on the base pan assembly (two
used) |
| Control Panel |
Q3949-60134 |
Control panel assembly - Includes
alphanumeric, menu, cancel, scan, copy, and fax buttons and the
display - Does NOT include the bezel - Mounts on the front deck of
the scanner assembly |
|
Cover |
Q3948-40007 |
ADF cover assembly (ONLY) - Covers
the paper pickup and feed mechanism - Mounts on the left end of the
ADF and flatbed scanner lid assembly |
| RB2-9916-020CN |
Cover - For fuser motor |
| RB3-0120-020CN |
Solenoid cover (Steel) - For
magnetic wave sheilding |
| RB3-0166-000CN |
Bottom inner cover (Black) plastic -
One covers the paper feed sensor in the center and the other covers
sensor wires toward the right side - Mounts on the bottom of the
center frame assembly of the 250-sheet input tray assembly (two
used) |
| RB3-1032-000CN |
Fusing assembly upper cover - Ribbed
cover with end caps - Mounts to the top of the fusing assembly |
| RB3-1136-000CN |
Face-down paper output cover ('L'
shaped plastic) - Serves as the rear of the tray for the face-down
output on top of the printer - Mounts under the top rear cover
assembly |
| Q2665-60125 |
ADF paper seperation pad assembly -
Mounts in the center of the ADF separation pad frame assembly (At
the rear of the paper input tray) - Mounts below the pick roller in
the ADF assembly |
| RB2-9916-000CN |
Cover - For fuser motor - For the
engaging motor (PM704) - Mounts on the upper left side of the rear
frame assembly |
| RB3-1137-000CN |
I/O cover - Rectangular plastic
cover with a recessed cutout for the interface connectors - Mounts
on the right rear of the printer |
| RB3-1170-000CN |
Front cover - Mounts on the front of
the cassette assembly for the 250-sheet input tray assembly |
| Q3948-67914 |
Internal cover kit - Includes the
curved plastic cover (with recessed area for grasping the handle on
the imaging drum/transfer assembly) and the cartridge removal label
- Mounts towards the front of the printer just above multipurpose
tray (tray 1) |
| RB3-0052-000CN |
Gear Cover (Small Black plastic
cover) - Covers the left end of the feed drive shaft - Mounts
towards the left side of the middle frame assembly |
| RB3-0283-000CN |
Inner cover - Covers the bottom of
the connector that interconnects the input tray base to the printer
- Mounts on the bottom of the right side support frame/cover
assembly for the base of the 250-sheet tray assembly |
| RB3-0282-000CN |
Inner cover - Covers the small
interconnecting PC board - Mounts on top of the right side support
frame/cover assemly on the base of the 250-sheet feeder assembly |
| RB3-1131-000CN |
Left rear cover - 'U' shaped cover
that mounts on the under-side of the extension for the left scanner
hinge |
| RB3-1134-000CN |
Internal cover (ONLY) - Curved
plastic piece with recessed area for grasping the handle on the
imaging drum/transfer assembly - Mounts towards the front of the
printer just above the multipurpose tray |
| RB3-0104-000CN |
Roller cover - Covers the
multipurpose paper pickup roller assembly - Mounts on the lower
front of the front frame assembly |
| RB3-1128-000CN |
Left side cover (ONLY) - Does NOT
include the vent cover or power switch button - Mounts on the left
side of the printer |
| RB3-1168-000CN |
Left side support frame/cover
assembly - For the base on the 250-sheet input tray assembly |
| RB3-0120-000CN |
Solenoid cover (Steel) - For
magnetic wave sheilding - Mounts over the solenoid on the right side
of the front frame assembly |
| RG5-7598-000CN |
Left side cover assembly - Includes
the main cover, vent cover, power switch button, rod and spring (The
power switch is located on the low voltage power supply board) |
| RG5-7634-000CN |
Right side support frame/cover
assembly - Includes the frame/cover, printer interface connector,
cable, feed drive PC board, and snap-on lid - For the base on the
250-sheet input tray assembly |
| RB3-1087-000CN |
Top cover - Covers the top of the
left cover/support assembly on the base of the 250-sheet input tray
assembly |
| RB3-1135-000CN |
Lower front cover - Rectangular
plastic strip - Mounts just below the multipurpose input tray on the
front of the printer |
| RB3-1140-000CN |
Rear cover / face-up output tray
(ONLY) - When opened, routes printed pages to this cover/tray for
face-up output - Mounts to the lower rear cover on the fusing
assembly |
| RG5-7604-000CN |
Rear cover/face-up output tray
assembly - Includes the tray/cover and the lower fusing assembly
cover - When opened, routes printed pages to this cover/tray for
face-up output - Mounts to the rear of the fusing assembly |
| RB3-1132-000CN |
Right rear cover - 'U' shaped cover
that mounts on the under-side of the extension for the right scanner
hinge - Covers the scanner interconnection cables |
| RG5-7599-000CN |
Right side cover assembly - Includes
the right side cover, DIMM memory access door, and the formatter
grounding plate |
| RG5-7597-000CN |
Top cover assembly - Includes the
rear cover with molded-in face-down output tray and the lift-up
toner cartridge / imaging drum and transfer assembly cartridge
access door - Does NOT include the upper front cover - Mounts to the
top of the printer |
| RB3-1125-000CN |
Upper front cover - Rectangular
plastic piece with recess for the printer logo - Mounts to the
cartridge access cover assembly |
| RB3-1126-000CN |
Upper left cover - Small cover that
is part of the inner side wall in the cartridge access area and
provides support for the exterior left side cover |
| RB3-1130-000CN |
Upper rear cover assembly - Also
guides the paper from the fusing assembly to the top output (face
down) tray - Mounts on the upper rear of the printer mechanism |
| RF5-4053-000CN |
Upper right cover - Small cover that
has a cutout for the scanner release button - Mounts on the upper
right side of the printer |
| RF5-4054-000CN |
Upper right cover assembly -
Includes the cover and clear plastic door - Small cover that has a
cutouts for the scanner release button and camera (photo) memory
interface card slots (Does NOT include the PC boards) - Mounts on
the upper right side of the |
| RB3-1139-000CN |
Vent cover - Rectangular plastic
cover with molded-in ventilation louvers - Mounts on the left side
cover |
|
Cross-Brace |
RB3-0108-020CN |
Metal support cross-brace - Mounts
on the top rear of the left and right support frame/cover assemblies |
| RB3-0108-000CN |
Metal support cross-brace - Mounts
on the top rear of the left and right support frame/cover assemblies
- For the base on the 250-sheet input tray assembly |
| Damper |
RB2-6248-000CN |
Damper assembly (Gray plastic piece
with small 13-tooth gear on it) - Helps to reduce clunking when the
paper pickup roller is engaged - Engages the paper pickup roller -
Mounts on the right side of the front frame assembly |
|
Door |
RF5-4055-000CN |
Cartridge access door (ONLY) -
Provides access to the toner cartridges and imaging drum/transfer
assembly cartridge - Does NOT include the upper front cover - Mounts
to the top rear cover |
| RB3-1138-000CN |
Memory access door - Provides access
for changing or adding DIMM memory modules to the printer - Mounts
to the right side cover |
| Drive Assembly |
RG5-7842-000CN |
Rotary drive assembly - Includes the
carousel rotating motor (DCM703), toner cartridge drive motor
(PM705), developing rotary stopper solenoid (SL93), bracket, and
gears - Mounts on the right top rear of the print engine |
|
Drum |
Q3964-67901 |
Imaging drum/transfer assembly
cartridge - Inserts into printer through the top door - Life
expectancy is 20,000 pages for black print ONLY, 5,000 pages for
color (typical combined life is approximately 8,000 to 10,000 pages) |
| Q3964A |
Imaging drum/transfer assembly
cartridge - Inserts into printer through the top door - Life
expectancy is 20,000 pages for black print only, 5,000 pages for
color (typical combined life is approximately 8,000 to 10,000 pages) |
| Fan |
RH7-1630-000CN |
Cooling fan (Panaflo Model FBA08T24H
- 80mm X 80mm X 15mm high, DC brushless, 24V DC, 190mA) - (FM712)
Mounts in the airflow guide/fan bracket assembly on the left side of
the printer |
|
Flag |
Q3948-67902 |
ADF paper sensor flag replacement
kit - Includes the paper sensor flag and spring - Mounts in the top
of the ADF cover |
| RB3-0111-000CN |
Paper flag - Plastic rod with paper
sensing flag on one end and sensor activator flag on the other -
Senses paper coming from the multi-purpose front input tray (tray 1) |
| RB3-0132-000CN |
Mechanical sensor flag (black
plastic) - For the paper feed sensor - Mounts on top of the center
frame assembly - For the base on the 250-sheet input tray assembly |
| RB3-0135-000CN |
Test print flag (Black lever) - Used
to activate the print engine test switch - Mounts in a metal holder
in the upper left of the front frame assembly |
| C7309-40013 |
Paper sensor flag - Senses when
there is a document in the automatic document feeder input tray -
Mounts in the top of the ADF cover |
| RB2-9925-000CN |
Sensor arm and flag - Activates the
photosensor (Does NOT include the roller) - For the Leading edge
paper sensor for the fusing assembly (PS720) - Protrudes up through
the feed plate on the middle frame assembly |
| RB3-0130-000CN |
Shaft mounted sensor flag (black
plastic) - For the paper out sensor - Mounts on the paper pickup
roller drive shaft - For the base on the 250-sheet input tray
assembly |
|
Foot |
RB3-1147-000CN |
Rear foot - Helps in printer
stability when the scanner has been lifted up - Also forms a recess
for the alignment peg on the optional paper tray - Mounts on the
rear of the printer below the I/O cover |
| RB2-6297-000CN |
Rubber foot - Square self-adhesive
rubber foot - Attaches to the rear of the middle frame assembly (two
used) |
| Frame |
Q1636-40037 |
ADF glass retainer (C-shaped plastic
frame) - Holds the ADF glass in place - Mounts on the left end of
the flatbed scanner assembly |
|
Fusing Assembly |
RG5-7602-000CN |
Fusing assembly - Includes the
fusing mechanism, lower rear cover (with the two locking levers),
and the rear cover / face-up output tray - Bonds the toner to the
paper with heat - For 110V to 127VAC operation - Slides in the lower
rear of the print engine |
| RG5-7603-000CN |
Fusing assembly - Includes the
fusing mechanism, lower rear cover (with the two locking levers),
and the rear cover / face-up output tray - Bonds the toner to the
paper with heat - For 220V to 240VAC operation - Slides in the lower
rear of the print engine |
|
Gear |
RB3-0092-000CN |
15 tooth gear with drive shaft
(Black plastic) - Used as part of the mechanism to disengage the
drive cams for the imaging drum/transfer assembly - Mounts on the
right side metal chassis frame |
| RS7-0582-000CN |
28 tooth idler gear - Mounts to the
upper right side of the fusing assembly |
| RB3-0091-000CN |
16 tooth gear (Black plastic) - Gear
with large stop tooth and shaft lock tab - Used as part of the
mechanism to disengage the drive cams for the imaging drum/transfer
assembly - Mounts on the inside of the right side metal chassis
assembly |
| RS7-0430-000CN |
26 tooth gear - White gear with
1/8th portion of gear cut away and pin for spring tensioning -
Mounts on the end of the paper pickup roller in the base on the
250-sheet input tray assembly |
| RS7-0580-000CN |
30 tooth gear - Main drive gear for
the fusing assembly - Mounts on the end of the pressure roller drive
shaft |
| RS7-0573-000CN |
186 tooth gear - Uppermost large
gear that mounts on a short shaft between the gear retainer bracket
and the right side plate front assembly |
| RB3-0022-000CN |
22 tooth gear (Black plastic) -
Small gear with diagonally cut teeth - Idler gear between the
transfer roller assembly and the feed drive shaft - Mounts on the
left side of the middle frame assembly |
| RS7-0418-000CN |
26 tooth gear (Black plastic) - Has
1/8th portion of gear cut away - Mounts on the end of the paper
pickup roller for the multipurpose input tray (Tray 1) |
| RS7-0429-000CN |
26 tooth gear (White plastic) - Has
recess for shaft drive pin - Paper pickup clutch drive gear - Mounts
between the right side of the front fame assembly and the paper
pickup gear plate assembly |
| RS7-0428-000CN |
30 tooth gear (White plastic) -
Mounts on the end of the registration roller drive shaft |
| RS7-0425-000CN |
30 tooth gear (White plastic) - Part
of the drive gears for the registration roller - Mounts on inside of
the front frame assembly on the right side |
| RS7-0437-000CN |
51 tooth gear (White plastic) - Main
drive gear for both the upper and lower top bin output rollers |
| RS7-0570-000CN |
81 tooth gear - Mounts on a pin on
the right side plate front assembly (between the gear retaining
bracket and the right side plate) |
| RS7-0424-000CN |
Dual gear - 20 tooth / 40 tooth -
Mounts between the right side of the front frame assembly and the
paper pickup gear plate assembly |
| RS7-0571-000CN |
Dual gear - 23 tooth / 54 tooth -
Small gear that mounts toward the front on a short shaft between the
gear retainer bracket and the right side plate front assembly |
| RS7-0426-000CN |
Dual gear - 26 tooth / 50 tooth
(White plastic) - Part of the drive gears for the registration
roller - Mounts on inside of the front frame assembly on the right
side |
| RS7-0572-000CN |
Dual gear - 31 tooth / 90 tooth -
Mounts on a pin on the right side plate front assembly (between the
gear retaining bracket and the right side plate) |
| RS7-0574-000CN |
Dual gear - 32 tooth / 123 tooth -
Large gear which mounts toward the front on the right side plate
front assembly |
| RS7-0435-000CN |
Dual gear - 32 tooth / 37 tooth
(White plastic) - Drives the upper top bin output roller - Mounts on
the right side of the rear frame assembly |
| RS7-0436-000CN |
Dual gear - 37 tooth / 43 tooth
(White plastic) - Part of the gear train for driving the upper top
bin output roller - Mounts on the right side of the rear frame
assembly |
| Q3948-67916 |
Paper output gear kit - Includes the
32 tooth / 37 tooth dual gear, the 37 tooth / 43 tooth dual gear,
and the 51 tooth gear - Mounts on the right side of the rear frame
assembly |
|
Gear Assembly |
Q3948-67913 |
Front frame gear kit - Includes the
20 tooth/40 tooth dual gear, 26 tooth gear, metal plate with two
gears assembly and the bushing for the paper pickup clutch gear
shaft - All mount on the right side of the front frame assembly |
| RG5-6938-030CN |
Gear assembly - Metal plate with two
White plastic gears attached |
| RG5-6938-000CN |
Gear assembly - Metal plate with two
White plastic gears attached - Part of the drive gears for the paper
pickup roller for the multipurpose input tray (tray 1) - Mounts on
the right side of the front frame assembly |
| Glass Assembly |
Q3948-67906 |
ADF glass window replacement kit -
Includes the small glass window, the 'U' shaped window frame, and
mounting screw - Mounts on the left end of the scanner assembly -
Used when scanning documents from the ADF assembly |
| Ground Plane |
RB3-0137-000CN |
Grounding plate - Grounds the paper
feed roller - Mounts towards the right end of the center frame
assembly - For the base on the 250-sheet input tray assembly |
|
Guide |
RB2-9903-000CN |
Cable guide (Quartz Gray plastic) -
Protects and supports the upper cable assembly - Mounts to the right
rear on the laser/scanner support assembly |
| RB3-1088-000CN |
Transfer inlet guide assembly -
Angled metal guide between the registration roller and the transfer
roller - Mounts to the middle frame assembly |
| RG5-7577-030CN |
Lower guide assembly - Includes the
support structure, delivery roller, drive gear, paper photo-sensor,
sensor flags, and upper separation guide |
| RG5-7584-000CN |
Paper guide assembly - Paper width
adjustable guide assembly for the multipurpose front input tray
(tray 1) - Mounts with the two hinges on the lower portion of the
front frame assembly |
| RF5-4065-000CN |
Entrance guide assembly - Mounts in
front of the tranfer roller assembly (behind the transfer inlet
guide) |
| RG5-7577-000CN |
Lower guide assembly - Includes the
support structure, delivery roller, drive gear, paper photo-sensor,
sensor flags, and upper separation guide - Mounts on the rear of the
fuser support frame assembly |
| RB3-0180-000CN |
Paper inlet guide - Small ribbed
plastic piece - Mounts on the lower front of the fusing assembly |
| RG5-6935-020CN |
Left cartridge guide assembly - |
| RB2-9954-000CN |
Left paper feed guide (small Black
plastic arm) - Mounts to the left of the separation pad assembly on
the lower front frame assembly |
| RG5-7576-000CN |
Separation upper guide assembly -
Ribbed plastic channel with pivot pins on each end and two pinch
rollers for the paper delivery roller - Mounts just behind the
pressure roller in the fusing assembly |
| RB2-9955-000CN |
Right paper feed guide (small Black
plastic arm) - Mounts to the right of the separation pad assembly on
the lower front frame |
| RB2-9852-000CN |
Rotary release guide - Small plastic
clip that allows for manual carousel rotation (with a straightened
paper clip) for removing toner cartridges without power - Mounts in
the top front of the rotary drive assembly |
|
Heating Roller |
RG5-7162-000CN |
Fusing film assembly (for 110VAC to
127VAC operation) - Includes the heater assembly and the fusing film
tube |
| RG5-7163-000CN |
Fusing film assembly (for 220VAC to
240VAC operation) - Includes the heater assembly and the fusing film
tube |
|
Hinge |
Q3948-67905 |
ADF assembly hinge kit - Includes
the left and right hinges and mounting screws - Mounts to the back
of the lid (document cover) on the ADF assembly |
| RB9-0889-000CN |
Tray hinge - 'L' shaped plastic arm
- For the left side of the multi-purpose front input tray (tray 1) -
Mounts in the lower portion of the front frame assembly |
| RB9-0890-000CN |
Tray hinge - 'L' shaped plastic arm
- For the right side of the multipurpose front input tray (tray 1) -
Mounts in the lower portion of the front frame assembly |
|
Holder |
RB3-0006-000CN |
Holder - Housing for the fusing
connector assembly - Mounts on the lower base pan of the printer
mechanism |
| RB3-1029-000CN |
Gear holder - Hollow tube with
locking tab - Retains the idler gear on the right side of the fusing
assembly |
| RB3-0023-000CN |
Interlock switch holder (Quartz Gray
plastic) - Does NOT include the micro-switch - Mounts on the support
shelf for the laser/scanner assembly (just to the left of the
laser/scanner assembly) |
| RB2-9924-000CN |
Sensor assembly mounting holder -
Holds the leading edge paper sensor (PS720) for the fusing assembly
- Mounts on the underside left on the middle frame assembly |
| Hook |
RB1-2190-000CN |
Pickup roller spring hook - Clips on
the pin of the drive gear for the pickup roller and hooks the
tensioning spring - For the base on the 250-sheet input tray
assembly |
|
Insulator |
RB3-1110-000CN |
Insulating sheet (Transparent
plastic) - For the power supply base assembly - Mounts to the
underside of the middle frame assembly |
| RB3-0007-000CN |
Insulating sheet (Transparent
plastic) - Mounts between the bottom pan and the high and low
voltage power supply boards |
| RB3-1379-000CN |
Insulator sheet - 'L' shaped plastic
insulator sheet - Protects the camera (photo) memory interface
assembly from shorting against the support bracket - Mounts on the
front support bracket on the right support assembly |
|
Interface
(Product) |
J7942G |
HP JetDirect en3700 external print
server - Fast Ethernet Internet connector for sharing peripherals
with USB ports, in a 10/100 TX LAN environment - Has one USB 2.0
printer port and one RJ-45 10/100 Base-TX connector - Includes
software and power module |
| J7942A |
HP JetDirect en3700 external print
server - Fast Ethernet Internet connector for sharing peripherals
with USB ports, in a 10/100 TX LAN environment - Has one USB 2.0
printer port and one RJ-45 10/100 Base-TX connector - Includes
software and power module |
| J7951G |
HP Jetdirect ew2400 802.11g wireless
print server module |
| J7951A |
HP Jetdirect ew2400 802.11g wireless
print server module |
|
Laser/Scanner |
RG5-6890-030CN |
Laser/scanner assembly |
| RG5-6890-000CN |
Laser/scanner assembly - Mounts in
the center of the scanner support assembly |
|
Lever |
RB3-1167-000CN |
Left pressure release lever - To
release pressure between the pressure roller and the heater assembly
to clear paper jams - Mounts on the left side of the fuser support
frame assembly |
| RB3-0179-000CN |
Left side lock release lever - Part
of locking system used to secure the fusing assembly in the printer |
| RB3-1166-000CN |
Right pressure release lever - To
release pressure between the pressure roller and the heater assembly
to clear paper jams - Mounts on the right side of the fuser support
frame assembly |
| RB3-0178-000CN |
Right side lock release lever - Part
of locking system used to secure the fusing assembly in the printer |
|
Link |
RG5-7645-000CN |
Left scanner link assembly - Spring
loaded arm - Connects between the top of the printer and the bottom
of the scanner - Allows for limited tilting of the scanner assembly
for toner cartridges and image drum/transfer assembly cartridge
access |
| Q3948-67909 |
Right link mount kit - Includes
the'L' shaped plastic piece that has a recess for the
printer-to-scanner link and scanner hinge, and the scanner release
lift spring - Mounts on the upper rear right side of the print
mechanism |
| RG5-7630-000CN |
Right scanner link assembly - Spring
loaded arm - Connects between the top of the printer and the bottom
of the scanner - Allows for limited tilting of the scanner assembly
for toner cartridges and image drum/transfer assembly cartridge
access |
| Memory (DIMM) |
C9121-67901 |
128MB, 100-pin SDRAM DIMM memory
module - (Part of C9121A) |
|
Memory (Product) |
C9121A |
128MB, 100-pin SDRAM DIMM memory
module |
| C7845A |
32MB, 100-pin SDRAM DIMM memory
module |
| C9680A |
64MB, 100MHz SDRAM DIMM memory
module |
|
Motor |
RH7-1628-000CN |
Fusing motor assembly - 24VDC motor
mounted on a motor controller PC board - (DCM702) Mounts on the
right side plate assembly (next to the DC controller board) |
| RF5-4063-030CN |
Main motor assembly - Large motor
mounted on a controller PC board |
| RF5-4063-000CN |
Main motor assembly - Large motor
mounted on a controller PC board - (DCM701) Mounts on the inside of
the metal right side frame assembly |
| RH7-1651-000CN |
Rotary motor assembly - (DCM703)
Rotates the four color toner cartridges in the carousel to position
one of them for printing - Mounts in the rotary drive assembly |
| RH7-1629-000CN |
Stepping motor - 24VDC - (PM704)
swings (or engages) the toner cartridge carousel in place to
transfer toner - Mounts on the left side of the rear frame assembly |
| RH7-1625-000CN |
Stepping motor - 24VDC - (PM705)
used to drive the internal rollers and mechanisms in the toner
cartridge when it has been rotated in the printing position on the
carousel - Mounts in the rotary drive assembly |
|
Mount |
RB3-1154-000CN |
Left link mount - Rectangular
plastic piece that has a recess for the printer-to-scanner link and
includes the bottom half of the scanner hinge - Mounts on the upper
rear left side of the print mechanism |
| RB3-1146-000CN |
Mount retainer - Holds the spring
loaded power switch rod on the left side cover |
| RB3-1158-000CN |
Right link mount - 'L' shaped
plastic piece that has a recess for the printer-to-scanner link and
includes the bottom half of the scanner hinge - Mounts on the upper
rear right side of the print mechanism |
|
PC Board |
RG5-7617-000CN |
Interconnecting feed drive PC board
- Mounts in the right side support frame/cover assembly of the
250-sheet input tray assembly |
| RG5-7609-000CN |
Carousel position and toner level
photoelectric sensor PC board - 'L' Shaped PC board with the two
sensors - (PS51) Mounts on the left plate in the toner cartridge
carousel assembly |
| RG5-7646-000CN |
DC controller board - Mounts on the
right side of the printer (Behind the formatter board assembly) |
| RH7-7158-000CN |
Density photoelectric sensor PC
board - (PS81) Mounts under the light blocking pad on the top of the
front frame assembly |
| Q3948-69001 |
Formatter assembly - Includes the
formatter PC board, the metal card cage cover, and cover plate -
Mounts on the right side of the print mechanism |
| RG5-7613-000CN |
Registration sensor PC Board - Small
board with flag activated photosensor - (PS711) Mounts in the
registration assembly on the underside of the middle frame |
| WG8-5593-000CN |
Sensor PC board - Small board with
flag activated photosensor - (PS718) Detects paper from the
multipurpose input tray, mounts on the right side of the front frame
assembly - (PS720) Front of page sensor for the fusing assembly,
mounts on the underside of |
| RG5-7612-000CN |
Top of page photoelectric sensor PC
board - Includes the photoelectric top of page sensor and the print
engine test switch - Mounts on the right side of the printer (Behind
the formatter board assembly) |
| RG5-7648-000CN |
Waste toner sensor assembly PC board
- Detects excess level of waste toner in the imaging drum/transfer
assembly cartridge - Mounts on the right side of the front frame
assembly |
|
Pad |
RF5-4012-000CN |
Separation pad assembly - Includes
the separation pad, holder and spring - Mounts below the
multipurpose front input (Tray 1) pickup roller assembly |
| RF5-4047-000CN |
Light blocking pad assembly - Black
plastic frame with soft rubber gasket and stiff conductive Mylar
piece (grounded) - Mounts to the top center of the front frame
assembly |
| RF5-4258-020CN |
Separation pad assembly - Includes
the gray plastic frame with the rubber insert strip |
| RF5-4258-000CN |
Separation pad assembly - Includes
the gray plastic frame with the rubber insert strip - For the
cassette on the 250-sheet input tray assembly |
| Pickup Assembly |
Q3948-67903 |
Paper pickup module - Paper pickup
roller assembly and screws |
|
Plate |
RB3-0010-030CN |
Feed plate - Center metal plate with
slots that the ribs on the middle frame assembly go through - |
| RB3-0286-000CN |
Contact plate - Runs between the
shaft on the registration roller and the metal entrance guide
assembly |
| RB3-1113-000CN |
Grounding plate - Small plate with
grounding finger - Grounds the end of the carousel drive shaft -
Mounts towards the top on the left side plate assembly |
| RF5-4060-000CN |
Base plate - Bottom support plate
for the fusing assembly |
| RB3-0065-000CN |
Contact plate - copper clad metal
spring - Holds the left end of the small 500 Meg-ohm resistor -
Mounts on the left side of the middle frame below the entrance guide
assembly |
| RB3-1024-000CN |
Pressure plate - Small steel channel
shaped plate - Spring loaded plate that provides upward force on the
pressure roller (two used) |
| RB3-0066-000CN |
Contact plate - copper clad metal
spring - Holds the right end of the small 500 Meg-ohm resistor -
Mounts on the left side of the middle frame below the entrance guide
assembly |
| RB2-9850-020CN |
Terminal contact plate - Provides
for a connection between the high voltage cable assembly and the
front toner cartridge contact spring - Mounts on the underside left
of the middle frame assembly |
| RB2-9851-020CN |
Terminal contact plate - Provides
for a connection between the high voltage cable assembly and the
rear toner cartridge contact spring - Mounts on the underside left
of the middle frame assembly |
| RB3-0057-000CN |
Transfer slide plate - Small 'U'
shaped metal insert plates - Mount in the bushing wells for the
transfer roller on the middle frame assembly (two used) |
|
Power Cord |
8121-0729 |
Power cord (Black) - 18 AWG, three
conductor, 1.9m (75in) long - Has straight (F) C13 receptacle (For
220V in Argentina) |
| 8121-0735 |
Power cord (Black) - 18 AWG, three
conductor, 1.9m (75in) long - Has straight (F) C13 receptacle (For
220V in Chile) |
| 8121-0734 |
Power cord (Black) - 18 AWG, three
conductor, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (For
220V in Brazil and Thailand) |
| 8121-0740 |
Power cord (Black) - 3-wire, 18 AWG,
1.9m (75in) long - Has straight (F) C13 receptacle (for 120V in the
USA, Canada, Mexico, and Taiwan) |
| 8121-1004 |
Power cord (Flint Gray) - 1.9m
(6.25ft) long - Has straight (F) C13 receptacle (For 220V in Israel) |
| 8121-0780 |
Power cord (Flint Gray) - 17 AWG,
2.3m (7.5ft) long - Has straight (F) C13 receptacle (For 240V in
India) |
| 8120-8707 |
Power cord (Flint Gray) - 17 AWG,
2.3m (7.5ft) long - Has straight (F) C13 receptacle (for 220V in
China) |
| 8120-8382 |
Power cord (Flint Gray) - 18 AWG,
1.8m (6.0ft) long - Has straight (F) receptacle (For 120V in the USA
and Canada) |
| 8121-0518 |
Power cord (Flint Gray) - 18 AWG,
1.9m (6.25ft) long - Has straight (F) C13 receptacle (For 220V in
Denmark) |
| 8121-0519 |
Power cord (Flint Gray) - 18 AWG,
1.9m (6.25ft) long - Has straight (F) C13 receptacle (For 220V in
Switzerland) |
| 8121-0520 |
Power cord (Flint Gray) - 18 AWG,
1.9m (6.25ft) long - Has straight (F) C13 receptacle (For 240V in
India) |
| 8121-0516 |
Power cord (Flint Gray) - 18 AWG,
1.9m (6.25ft) long - Has straight (F) receptacle (For 220V in
Europe) |
| 8121-0517 |
Power cord (Flint Gray) - 18 AWG,
1.9m (6.25ft) long - Has straight (F) receptacle (For 240V in the
UK, Hong Kong, Singapore, and Malaysia) |
|
Power Supply |
RG5-7647-000CN |
High voltage power supply board
(HVT) assembly - Has contacts for the eight high voltage springs in
the printer - Mounts in the bottom pan assembly (Towards the front
of the printer) |
| RH3-2260-000CN |
Low voltage power supply - For
110VAC to 127VAC operation - Includes the AC power input connector
and power switch - Mounts in the bottom pan assembly towards the
rear of the printer |
| RH3-2261-000CN |
Low voltage power supply - For
220VAC to 240VAC operation - Includes the AC power input connector
and power switch - Mounts in the bottom pan assembly towards the
rear of the printer |
| RG5-7616-000CN |
Sub-high voltage board - Small
auxillary PC board - Mounts in a holder just above the high voltage
board in the bottom pan assembly |
| Pressure Assembly |
RG5-7589-000CN |
Carousel pressure (support) assembly
- Includes the main rear support, E-label reader assembly, engaging
sensor, and the engaging rod shaft - Primary support structure for
the toner cartridge carousel |
|
Pulley |
RB3-0067-000CN |
Pulley roller (accommodates one feed
belt) - Small black roller approximately 1.59cm (5/8 inch) long with
one ball type pulley - Mounts just behind the transfer roller in the
middle frame assembly (two used) |
| RB3-0061-000CN |
Pulley roller (accommodates three
feed belts) - Small black roller approximately 3.49cm (1-3/4 inches)
long with three ball type pulleys - Mounts just behind the transfer
roller in the middle frame assembly (two used) |
| Rack Slide |
RB3-0090-000CN |
Rack slide - White plastic piece
with gear teeth layed out in rack form on both sides - Part of the
mechanism that disengages the imaging drum/transfer assembly cams
when the top cover is opened - Mounts vertically on the metal right
side frame |
|
Reader |
RG5-7131-000CN |
E-label reader (contact board only)
- Connects the cartridge non-volitale memory to the DC controller
board - Mounts to the top left on the front frame assembly |
| RG5-7132-000CN |
E-label reader assembly - Connects
cartridge non-volatile memory to the DC controller board - For the
toner cartridges - Mounts on top of the toner cartridge carousel
assembly |
| Resistor |
RH5-3169-000CN |
Resistor - 500 Meg ohm, 300mW -
Mounts on the left side of the middle frame below the entrance guide
assembly - Held in place with two small contact plates |
|
Rod |
RB3-1145-000CN |
Power switch rod - Goes between the
power button and the power switch on the low voltage power supply
board - Mounts on the left side cover |
| Q3948-67911 |
Power switch rod kit - Includes the
power switch push rod, compression spring, and mount retainer -
Mounts on the inside of the left cover assembly |
|
Roller |
RB2-9950-000CN |
Pinch-roller - Small roller mounted
on a shaft - Rolls against the paper delivery roller in the fusing
assembly - Snaps in molded-in holders on the separation upper guide
assembly (two used) |
| RB3-0012-000CN |
Belt roller - Small oval shaped
roller approximately 1-3/4 inches long - Mounts toward the center of
the metal feed plate on the middle frame assembly |
| RB2-2904-000CN |
Guide roller (free spinning white
plastic roller) - Mounts on the paper pickup drive shaft on each
side of the pickup 'D' shaped roller - For the multipurpose front
input tray (tray 1) |
| RB3-0160-000CN |
Paper pickup roller ('D' shaped) -
Mounts on the paper pickup roller assembly for the multipurpose
front input tray (tray 1) |
| RB2-9909-000CN |
Pressure roller (small Black hard
plastic 'solid' roller) - Presses against the lower top bin output
roller on the middle rear of the printer (two used) |
| RF5-4068-000CN |
Pressure roller (small Black hard
plastic 'solid' roller) - Presses against the lower top bin output
roller on the middle rear of the printer (two used) |
| RB2-7195-000CN |
Sensor flag roller (small White
plastic roller) - Mounts in the sensor arm flag for the leading edge
paper sensor for the fusing assembly (PS720) |
|
Roller Assembly |
Q3948-60140 |
ADF pick roller assembly - Includes
two rollers in a bracket assembly - Moves the first few top pages of
the input stack where the top page is picked off and feed to the
pre-scan drive rollers - Mounts in the middle of the ADF assembly |
| RB3-0129-020CN |
Feed roller assembly - Includes the
metal shaft and two small rubber rollers |
| RB3-1034-000CN |
Pressure roller assembly - Hard
rubber roller on a metal drive shaft - Lower roller in the fusing
assembly |
| RG5-7595-000CN |
Lower top bin output roller assembly
- Includes the shaft with four rubber rollers, two bushing/shaft
retainers, and the drive gear - Mounts in the center on the rear
frame assembly (above the fusing assembly) |
| RB3-0129-000CN |
Feed roller assembly - Includes the
metal shaft and two small rubber rollers - Feeds paper from the
paper cassette into the printer - Mounts on the top of the center
frame in the base on the 250-sheet input tray assembly |
| RG5-6952-020CN |
Paper pickup roller assembly -
Includes the shaft, guide assembly cams, the D-shaped roller, and
roller retainers - Picks paper from the multipurpose front input
tray (tray 1) |
| RB3-0161-000CN |
Paper pickup roller assembly -
Includes the 'D' shaped rubber roller on a plastic shaft - Mounts in
the lower center of the center frame assembly - For the base on the
250-sheet input tray assembly |
| RG5-6952-000CN |
Paper pickup roller assembly -
Includes the shaft, guide assembly cams, the D-shaped roller, and
roller retainers - Picks paper from the multipurpose front input
tray (tray 1) - Mounts in the lower portion of the front frame
assembly |
| RF5-4035-000CN |
Pressure roller and arm assembly -
Includes the small white roller, the holding arm, and roller scraper
- Rolls against the rubber feed rollers (two used) - For the base on
the 250-sheet input tray assembly |
| RG5-6939-020CN |
Registration roller assembly -
Includes the roller, bushings, mounting plate, paper sensor, and the
sensor flag - Mounts from the bottom toward the front center of the
middle frame assembly |
| RF5-4067-030CN |
Transfer roller assembly - Long
black foam type roller - Transfers static charge to paper - Mounts
towards the front and on top of the middle frame assembly |
| RG5-7637-000CN |
Upper top bin output roller assembly
- Includes the shaft with four rubber rollers, two bushing/shaft
retainers, two anti-reversing flaps, and the drive gear - Mounts on
the top rear of the printer |
|
Roller Kit |
Q3948-67904 |
ADF pick roller assembly replacement
kit - Includes the pickup roller assembly (two rollers in a
bracket), separation pad, mounting screws, and illustrated
replacement instructions - Mounts in the middle of the ADF assembly |
| Q3948-67922 |
Lower face-down pressure roller kit
- Includes the two small Black hard plastic rollers and
corresponding torsion springs - Mounts on the back-side of the rear
frame assembly |
| Q3948-67912 |
Paper pickup roller kit - Includes
the 'D' shaped the paper pickup roller assembly and the separation
pad assembly - For the multipurpose front input tray (tray 1) |
| Q3948-67907 |
Paper pickup roller replacement kit
- Includes the pickup roller ('D' shaped roller), separation pad,
and illustrated instructions - Picks paper from the multipurpose
front input tray (tray 1) - Mounts in the lower portion of the frame
assembly |
| Q3948-67920 |
Transfer roller kit - Includes the
transfer roller, two transfer side plates ('U' shaped metal
inserts), the right end shaft bushing, and the two compression
springs at the left end of the roller - Mounts towards the front and
on top of the middle frame |
| Q3948-67917 |
Upper face-down pressure roller kit
- Includes the two small Black hard plastic rollers and
corresponding torsion springs - Mounts on the top rear of the rear
frame assembly |
| Scanner |
Q3948-60191 |
Flatbed scanner assembly - Does NOT
include the ADF assembly - Mounts to the top of the printer |
|
Screw |
XA9-1501-000CN |
M3 pan-head Phillips screw - 10mm
long - Used to secure the fusing assembly drive motor to the right
side plate (four used) |
| XA9-1500-000CN |
M3 pan-head Phillips screw with flat
washer - 8mm long - Used to secure the fusing connector holder to
the base pan assembly and the fusing assembly upper cover to the
structure |
| XB4-5300-809CN |
M3 pan-head phillips screw with
plastite threads - 8mm long - Used to secure the power button mount
to the left side cover |
| XA9-1449-000CN |
M3 pan-head Phillips screw with
machine threads - 8mm long - Used to secure the thermistor to the
right side plate and the power supply PC boards and holders the the
base pan assembly and the ground terminal to the fuser support frame |
| XB4-7401-005CN |
M4 pan-head phillips screw with
self-tapping threads - 10mm long |
| XB2-4300-605CN |
M3 pan-head phillips screw with flat
washer - 6mm long - Secures the terminals from the high voltage
cable assembly to the contact plates on the left side of the middle
frame assembly (two used) |
| XA9-0267-000CN |
M3 screw - 6mm long - Used to secure
the top of page sensor to the mounting bracket |
| XA9-0849-000CN |
M3 truss-head phillips screw with
machine threads - 6mm long - Primarily used to secure metal to metal
parts |
| XA9-1495-000CN |
Wafer head machine screw - M3, 6mm
long, No. 2 Phillips recess - Secures metal to sheet metal - Used
internally to secure brackets, plates, the pickup solenoid, and the
drive motor to the left and right side plates |
|
Shaft |
RB2-4933-000CN |
Lock release shaft - Small shaft
with locking tab - Does NOT include the lock release lever - Used to
secure the fusing assembly in the printer (two used) |
| RB3-0011-000CN |
Feed drive shaft - Long shaft with
eight feed belt ball type pulleys and one ribbed feed guide drive
belt pulley - Mounts behind the transfer roller on the middle frame
assembly |
| RB3-0060-020CN |
Idler gear shaft - Short metal rod -
Shaft for the transfer and feed drive idler roller - Mounts on the
left side of the middle frame assembly |
| Q3948-67919 |
Feed shaft kit - Includes the feed
drive shaft, the belt roller, the idler gear shaft, and the 23 tooth
idler gear - Mounts just behind the transfer roller in the middle
frame assembly |
|
Shield |
RB2-9932-000CN |
RFI shield - Parallel wire form
mounted over the fan - Mounts on the fan air duct assembly on the
left side of the printer |
| RB3-0136-020CN |
Solenoid cover/magnetic shield -
Mounts on the right end of the center frame assembly (over the
pickup solenoid) - For the base on the 250-sheet input tray assembly |
| Shutter |
RG5-6940-050CN |
Registration shutter assembly -
Includes the metal roller, mounting frame, grounding springs, and
the dual coupling gear - Mounts over the registration roller at the
front of the middle frame assembly |
|
Sideplate |
RG5-6942-030CN |
Left side carousel plate assembly -
End plate under the rotational toner cartridge carousel - Includes
all of the high voltage contacts for the toner cartridges |
| RG5-7581-060CN |
Right side plate front assembly -
Includes the front half of the metal frame assembly, gears, imaging
drum/transfer assembly drive cams, cover engaging mechanism, roller
engaging clutch (CL2), and main drive motor (DCM701) - Mounts on the
right side |
| RG5-6942-000CN |
Left side carousel plate assembly -
End plate under the rotational toner cartridge carousel - Includes
all of the high voltage contacts for the toner cartridges - Mounts
on the metal carousel support frame |
| RG5-7579-070CN |
Main drive (right side plate)
assembly - Includes the right side plate front assembly (with main
motor, clutch, and gears) and the right side plate rear assembly
(with drive gears) |
| RG5-7579-000CN |
Main drive (right side plate)
assembly - Includes the right side plate front assembly (with main
motor, clutch, and gears) and the right side plate rear assembly
(with drive gears) - Mounts on the right side |
| RG5-7581-000CN |
Right side plate front assembly -
Includes the front half of the metal frame assembly, gears, imaging
drum/transfer assembly drive cams, cover engaging mechanism, roller
engaging clutch (CL2), and main drive motor (DCM701) - Mounts on the
right side |
| RG5-7580-020CN |
Right side plate rear assembly -
Includes the rear half of the metal right side plate and the two
associated gears |
| RG5-7580-000CN |
Right side plate rear assembly -
Includes the rear half of the metal right side plate and the two
associated gears - Mounts on rear half of right side of printer |
|
Solenoid |
RH7-5383-000CN |
Solenoid assembly - (SL92) Lever on
the solenoid disengages the stop on the drive gear on the paper
pickup roller for the multipurpose input tray (tray 1) - (SL92)
Lever on the solenoid disengages the stop on the drive gear on the
paper pickup roller for |
| RH7-5384-000CN |
Solenoid assembly - (SL93) Engages
to stop rotation when the proper toner cartridge on the carousel is
in place for printing |
|
Spacer |
RB2-9935-000CN |
Left spacer - Shipping lock for the
fusing assembly - Mounts in the lower rear cover of the fusing
assembly |
| RB2-9934-000CN |
Right spacer - Shipping lock for the
fusing assembly - Mounts in the lower rear cover of the fusing
assembly |
|
Spring |
C7309-80013 |
Torsion spring - For the ADF paper
sensor flag - Provides a slight amount of back pressure so the flag
will not mistakenly indicate a document |
| RB3-0015-000CN |
Compression spring - Provides upward
pressure for the left transfer roller bushing |
| RB3-0044-000CN |
Electrical contact spring - (Front)
Provides high voltage to the toner cartridge via a cable assembly
and connection through the carousel plate assembly - Connects to the
high voltage board |
| RB3-1025-000CN |
Compression spring - Provides upward
force on the pressure roller - Mounts between the two guide plates
and the fuser support frame assembly (two used) |
| RS6-2024-000CN |
Compression spring - Provides
pressure for the separation pad for the multipurpose tray (tray 1) -
Mounts in the lower center of the front frame assembly |
| RS6-2769-000CN |
Compression spring - Large spring
that provides upward pressure on the paper lift plate in the
cassette assembly in the 250-sheet input tray assembly |
| RS6-2771-000CN |
Compression spring - Provides
tension for the power switch button - Mounts on the left side cover |
| RB3-0016-000CN |
Electrical contact spring - Spring
steel wire with compression springs formed on both ends - One end
provides upward pressure on the right bushing for the transfer
roller - Connects to high voltage board |
| RB3-0046-000CN |
Electrical contact spring - Mounts
on the middle frame assembly behind the transfer roller - Of the
four similar springs, this one is just to the left of the one on the
far right - Connects to high voltage board |
| RB3-0122-000CN |
Left retaining spring - Helps to
secure the imaging drum/transfer assembly in the printer - Mounts on
the upper left side of the front frame assembly |
| RB3-1150-000CN |
Grounding spring - Mounts between
the fusing assembly lower rear cover and fuser support frame
assembly (two used) |
| RS6-2760-000CN |
Compression spring - Provides
pressure for the pressure rollers on the center frame assembly (two
used) - For the base on the 250-sheet input tray assembly |
| RS6-2772-000CN |
Torsion spring - Mounts on the right
link mount of the printer - Provides upward presure to help lift up
the scanner assembly when the scanner is unlatched |
| RB3-0042-000CN |
Electrical contact spring - Mounts
on the middle frame assembly behind the transfer roller - Of the
four similar springs, this one is next to the one on the far left -
Connects to high voltage board |
| RB3-0121-000CN |
Right retaining spring - Helps to
secure and ground the imaging drum/transfer assembly in the printer
- Mounts on the upper right side of the front frame assembly |
| RB3-1065-000CN |
Torsion spring - Provides pressure
for the lower top bin output pressure rollers (two used) |
| RB2-9905-000CN |
Torsion spring - Provides pressure
for the upper top bin output pressure rollers (two used) |
| RB3-0048-000CN |
Electrical contact spring - Mounts
on the middle frame assembly behind the transfer roller - Of the
four similar springs, this one is on the far left - Connects to the
high voltage board |
| RB9-0843-000CN |
Torsion spring - Provides a small
amount of back pressure for the paper sensor flag - For the base on
the 250-sheet input tray assembly |
| RS6-2766-000CN |
Tension spring - Provides a small
amount of return tension for the sensor flag arm on the leading edge
sensor for the fusing assembly (PS720) |
| RB2-9999-000CN |
Torsion spring - Secures the belt
roller (for the feed drive shaft) in the top of the middle frame
assembly |
| RB3-0043-000CN |
Electrical contact spring - Mounts
on the middle frame assembly behind the transfer roller - Of the
four similar springs, this one is on the far right - Connects to
high voltage board |
| RS6-2030-000CN |
Tension spring - Provides support
tension for the multipurpose front input tray guide assembly (two
used) |
| RB2-9952-000CN |
Tray 1 flag spring - Provides
torsion for the tray 1 paper sensor flag - Mounts in the lower
portion of the front frame assembly |
| RB3-0047-000CN |
Electrical contact spring - Mounts
on the underside of the middle frame assembly - Connects to high
voltage board |
| RB3-0045-000CN |
Electrical contact spring - Rear
electrical contact spring - Provides high voltage to the toner
cartridge via a cable assembly and connection through the carousel
plate assembly - Connects to the high voltage board |
| Standoff |
VT2-0012-005CN |
PC Board support - Plastic standoff
for supporting a PC board - Supports the high voltage board on the
base assembly metal pan (six used) |
| Static Dissipater |
RB3-0009-000CN |
Static eliminator ground plate -
Right angled metal piece with small teeth on top edge - Mounts from
underneath on the middle frame assembly just behind the pulley
rollers |
| Strip |
C7309-40153 |
Cleanout assembly strip - Green
plastic bar with two grab tabs - Can be removed to help clear paper
jams in the automatic document feeder assembly - Snap locks on the
back side (far left side) of the ADF assembly and runs the full
width of the paper path |
|
Support |
RB2-9976-000CN |
Cross-member support - 'L' shaped
bracket used to help support the camera (photo) memory card
interface boards - Mounts on the upper right front of the right side
frame assembly |
| RC1-1036-000CN |
Separation pad support - Pivoting
'L' shaped metal support frame (Does NOT include the separation pad
assembly) - For the cassette on the 250-sheet input tray assembly |
| RG5-6907-030CN |
Laser/scanner support assembly
(sheet metal plate) - Crossmember between the two side frames -
Support for the laser/scanner assembly, the toner cartridge carousel
drive motor, and the cover interlock switch assembly |
| RG5-7632-000CN |
Left support assembly - Metal frame
which supports the top mounted scanner - Mounts to the top of the
left side frame assembly |
| RB3-0062-000CN |
PC board support (Black plastic
holder) - For mounting the small sub-high voltage board above the
high voltage board |
| RG5-7631-000CN |
Right support assembly - Metal frame
which supports the top mounted scanner and the camera (photo) memory
interface board assembly - Also includes the scanner release
button/lever - Mounts to the top of the right side frame assembly |
| Switch |
RH7-6051-000CN |
Microswitch with lever activator -
(SW2) Senses when the top cover is open - Mounts in a holder on the
scanner support assembly |
| Thermistor |
RH7-7159-000CN |
Thermistor - Mounts to the metal
right side frame assembly just above the DC controller board |
|
Tray |
Q3948-60214 |
Paper input tray for the ADF
assembly - Includes the plastic try and width adjustment side rails |
| Q3952A |
Optional 250 sheet paper input tray
- Includes tray base which attaches to printer, and the slide out
paper tray - Accommodates 148mm x 210mm (5.8 x 8.3 inches) to 216mm
x 356mm (8.5 x 14 inches) media - Only one 250 sheet tray supported
per printer |
| RB3-0019-000CN |
Toner catch tray (curved Black
plastic piece) - Holds residual toner from photosensitive drum -
Mounts just below the toner cartridge carousel on the bottom frame
assembly |
|
Tray Assembly |
RG5-7601-000CN |
Multipurpose front input tray
assembly (tray 1) - Includes the front cover piece, pull-out paper
support, and the flip-out extender - Mounts on front of printer (on
the front frame assembly) |
| RG5-7635-000CN |
250-sheet paper cassette tray
assembly (complete) - Pull out cassette that the paper is loaded
into - Does NOT include the paper feed base assembly |
|
Tray Kit |
C9706-67901 |
Multipurpose tray (tray 1) service
kit - Includes one paper pickup roller and one separation pad
assembly |
| C9706-67902 |
Multipurpose tray (tray 1) service
kit with extra separation pads - Includes one paper pickup roller
and three separation pad assembly |
