|
Airflow Guide |
RB2-9904-000CN |
Airflow Guide (duct) - Black plastic insert
piece which runs the width of the printer and has an air flow hole
on right side - Directs air flow from the fan on the left side of
the printer to the fusing assembly - Snap locks in center rear of
printer |
|
RB3-0025-000CN |
Airflow guide (duct) / fan holder bracket
assembly (Quartz Gray plastic) - Mounts on the left metal side frame
assembly |
|
Arm |
RB3-0089-000CN |
Top cover rack arm (Black) - Plastic arm with
teeth on bottom edge - Disengages the imaging drum/transfer assembly
drive cams when the top door is open - Mounts on the right side of
the top cover door |
|
Belt |
RB1-8668-030CN |
Feed guide drive belt - Small belt
approximately 5/16 inch wide with 'A' shaped ribs on it - Between
the feed drive roller and the small center roller - Driven via the
transfer roller gear train |
|
RB3-0063-000CN |
Paper feed belt - Small black rubber belt
approximately 1/8 inch wide with little 'A' shaped ribs on it - Goes
between the feed drive roller and the pulley rollers (eight used) |
|
Bezel |
RB3-0035-000CN |
Interface bezel (Quartz Gray plastic) -
Vertical cover that surronds the interface connectors - Mounts on
the right rear of the printer |
|
Body |
RG5-6915-030CN |
250 sheet cassette tray main body assembly -
Includes the main structure frame, paper stops, lift plate, springs,
and the separation pad assembly - Does NOT include the blue plastic
front cover - For the cassette on the 250 sheet input tray assembly |
|
Bushing |
RB2-2895-000CN |
Shaft bushing/retainer - Right side pickup
roller support bushing - Mounts on and retains the right end of the
pickup roller shaft - For the base on the 250 sheet input tray
assembly |
|
RB2-2896-000CN |
Shaft bushing/retainer - Left side pickup
roller support bushing - Mounts on and retains the left end of the
pickup roller shaft - For the base on the 250 sheet input tray
assembly |
|
RB2-2897-000CN |
Shaft bushing/retainer - Mounts on the gear
side of the drive shaft for the paper pickup roller assembly - For
the base on the 250-sheet input tray assembly |
|
RB2-2973-000CN |
Support bushing - Mounts on each end of the
pressure roller in the fusing assembly |
|
RB2-3043-000CN |
Left roller bushing - Acts as the bearing and
retainer for the left end of the paper pickup roller assembly (tray
1) - Mounts on the left side of the front frame assembly |
|
RB2-3044-000CN |
Right roller bushing - Acts as the bearing and
retainer for the right end of the paper pickup roller assembly (tray
1) - Mounts on the right side of the front frame assembly |
|
RB2-9808-000CN |
Bushing/shaft retainer assembly - Black plastic
- Holds the rotation drive shaft in the right side plate of the
toner cartridge carousel (rotary) assembly |
|
RB2-9809-000CN |
Bushing/shaft retainer assembly (White plastic)
- Holds the rotation drive shaft in the left side plate of the toner
cartridge carousel (rotary) assembly |
|
RB3-0014-000CN |
Bushing assembly (black plastic bushing with
small guide roller on top) - Holds the right end of the transfer
roller assembly in the bottom frame assmebly |
|
RS5-1635-000CN |
Shaft bushing - For the paper pickup clutch
gear shaft - Mounts on the plate of the multipurpose paper pickup
gear assembly |
|
RS5-1636-000CN |
Shaft bushing - Mounts on the gear end of the
feed roller shaft in the base on the 250-sheet input tray assembly |
|
RS5-1637-000CN |
Bushing (black plastic) - Mounts on the right
end of the registration roller assembly |
|
RS5-1638-000CN |
Bushing - For the registration roller gear
drive shaft on the right side of the front frame assembly, and the
left side of the feed roller in the 250-sheet paper input tray
assembly |
|
Cable |
C9706-60104 |
Flat flexible cable - From DC controller board
to formatter board |
|
RG5-6971-000CN |
Cable assembly (two 3-pin connectors and a spad
lug) - Power cable for the fusing assembly - From fusing assembly
connector to the chassis ground and the low voltage power supply
board |
|
RG5-6974-000CN |
Cable assembly - From toner cartridge E-label
reader assembly on the carousel to the DC controller board |
|
RG5-7106-000CN |
Cable assembly (two 2-pin connectors) -
Connects between the low voltage power supply board (J401) and the
formatter board (J1003) |
|
RG5-7107-000CN |
Cable assembly (8-pin, red wire) - (J402 to
J134) connects the low voltage power supply board to the DC
controller board |
|
RG5-7108-000CN |
Cable assembly (two 8-pin connectors, Purple
wire) - Connects between the low voltage power supply board (J403)
and the DC controller board (J133) |
|
RG5-7109-000CN |
Cable assembly (two 7-pin connectors) -
Connects between the DC controller board (J119) and the fusing
assembly connector (J201) |
|
RG5-7114-000CN |
Cable assembly (two 4-pin connectors) with
shield - Connects between the cartridge drive motor (J705) the DC
controller board (J106) |
|
RG5-7115-000CN |
Cable assembly (two 3-pin connectors) -
Connects between the roller engaging photosensor (J714) and the DC
controller board (J115) |
|
RG5-7117-000CN |
Cable assembly (two 3-pin connectors) -
Connects between the engaging sensor (J712) on the toner cartridge
carousel and the DC controller board (J125) |
|
RG5-7122-000CN |
Cable assembly - 'Y' type cable (three
connectors) - The 14-pin connector splits into an 8-pin connector
and a 6-pin connector - Connects between the DC controller board
(J118) and the optional paper tray connectors (J230) |
|
RG5-7123-000CN |
Grounding cable assembly - Connects from the
optional tray connector housing to the metal right side frame
assembly |
|
RG5-7126-000CN |
Cable assembly (two 5-pin connectors) -
Connects between the sub-high voltage board (J505) and the high
voltage board (J503) |
|
RG5-7128-000CN |
Cable assembly (four 3-pin connectors) -
Connects between the DC controller board (J107 and J138) and the
leading edge paper sensor for the fusing assembly (J720) and the
registration sensor (J711) |
|
RG5-7129-000CN |
Cable assembly (two connectors and two spade
lugs) - From toner cartridge contacts on the left carousel side
plate to the cable (J512 and J511) that runs to the high voltage
power supply board |
|
RG5-7130-000CN |
High voltage cable assembly - Connects between
the high voltage board spring contacts (on the middle frame
assembly) and the cables for the toner cartridge carousel left plate
assembly (J511 and J512) |
|
RG5-7138-000CN |
Cable assembly - From sensor (PS717) (which
senses paper feeding from optional tray 3) to the small
interconnecting PC board on the right side frame/cover assembly -
For the base on the 250-sheet input tray assembly |
|
RG5-7139-000CN |
Cable assembly - From paper out sensor (PS716)
to the small interconnecting PC board on the right side frame/cover
assembly - For the base on the 250-sheet input tray assembly |
|
RG5-7144-000CN |
Cable assembly (with seven connectors) - From
various upper level components to the DC controller board |
|
RG5-7145-000CN |
Front cable assembly (six connectors) - From
various components on the front frame assembly and right side to the
DC controller board |
|
RG5-7146-000CN |
High voltage cable assembly (two 15-pin
connectors and two 14-pin connectors) - Connects between the high
voltage power supply board (J501 and J502) and the DC controller
board (J136 and J135) |
|
RG5-7149-000CN |
Connector assembly - Includes the 14-pin (F)
interface connector and cable assembly - (Tray 2 to printer
connector) connects to the feed drive PC board in the cassette base
assembly |
|
RH2-5524-000CN |
Flat flexible cable (FFC) assembly - Connects
between the laser/scanner assembly (J11) the DC controller board
(J102) |
|
Cable (Interface) |
C2950A |
IEEE 1284 Bi-Tronics parallel cable - DB-25 (M)
connector (type A) to 36-pin Centronics (M) connector (type B) -
2.0m (6.6ft) long |
|
C2951A |
IEEE-1284 Bi-Tronics parallel cable - DB-25 (M)
connector (type A) to 36 pin Centronics (M) connector (type B) -
3.0m (9.8ft) long |
|
C6518A |
Universal Serial Bus (USB) interface cable -
Type 'A' connector to type 'B' connector - 2.0m (6.6ft) long |
|
Carousel |
RG5-6910-080CN |
Carousel (Rotary) assembly - Includes the
carousel assembly, the support assembly, end plates, drive gears and
shaft, sensors, and cables - Mounts towards the rear of the printer
in front of the rear frame assembly |
|
Cartridge |
C9700A |
HP Color LaserJet smart Black print cartridge -
Will print approximately 5,000 pages at 5% coverage |
|
C9701A |
HP Color LaserJet smart Cyan print cartridge -
Will print approximately 5,000 pages at 5% coverage |
|
C9702A |
HP Color LaserJet smart Yellow print cartridge
- Will print approximately 5,000 pages at 5% coverage |
|
C9703A |
HP Color LaserJet smart Magenta print cartridge
- Will print approximately 5,000 pages at 5% coverage |
|
C9700-67901 |
HP Color LaserJet smart Black print cartridge -
Will print approximately 5,000 pages at 5% coverage |
|
C9701-67901 |
HP Color LaserJet smart Cyan print cartridge -
Will print approximately 5,000 pages at 5% coverage |
|
C9702-67901 |
HP Color LaserJet smart Yellow print cartridge
- Will print approximately 5,000 pages at 5% coverage |
|
C9703-67901 |
HP Color LaserJet smart Magenta print cartridge
- Will print approximately 5,000 pages at 5% coverage |
|
Cleaning Supplies |
5090-3379 |
Toner cleaning cloth - Specially treated cloth
for absorbing toner (1 per package) - Ideal for clening up toner
spills |
|
Clip |
WT2-5056-000CN |
Cable clip - 'C' shaped White plastic - Mounts
in the opening on the cover for the paper pickup solenoid |
|
XD2-1100-502CN |
E-ring clip - Secures the dual gear to the
drive shaft which drives the registration roller - Located on the
inside of the front frame assembly |
|
XD9-0136-000CN |
Retaining E-ring - Mounts on the left end of
the paper feed roller assembly - For the base on the 250 sheet input
tray assembly |
|
Clutch |
RH7-5366-000CN |
Electromagnetic clutch assembly (24V) -
Electrical clutch between the clutch drive gear and shaft - (CL2)
Engages the roller within the imaging drum/transfer assembly from
the main gear train |
|
Connector |
RH2-5519-000CN |
Connector assembly - For optional paper tray -
One mounts to the bottom right side of the printer middle frame
assembly (interfaces 250 sheet tray), and the other to the bottom of
the 250 sheet tray base assembly (interfaces 500 sheet tray) - (two
used) |
|
RH2-5520-000CN |
Connector for the fusing assembly - Seven small
contol pins plus three separated high current pins - Mounts in the
connector housing mounted on the bottom pan of the printer |
|
WT2-5737-000CN |
Drawer connector - Connector located on bottom
of tray assembly frame on right side, which connects tray assemblies
to each other - Mounts on the bottom pan of the printer (two used) |
|
Control Panel |
RG5-6927-000CN |
Control panel assembly (mechanical only) -
Includes the 'Rotate Carousel', 'Cancel Job' and the 'Go' buttons,
plus the various indicator light pipes - All switches and LED's are
on the formatter PC board - Mounts to the top of the right cover
assembly |
|
Cover |
RB2-9916-000CN |
Cover - For fuser motor - For the engaging
motor (PM704) - Mounts on the upper left side of the rear frame
assembly |
|
RB3-0030-000CN |
Upper rear cover (Quartz Gray) - Mounts on the
upper rear of the printer above the face-up output tray door |
|
RB3-0032-000CN |
Face-down paper output L-Shaped cover ( Blue) -
Serves as the rear of the tray for the face-down output tray on top
of the printer |
|
RB3-0052-000CN |
Gear Cover (Small Black plastic cover) - Covers
the left end of the feed drive shaft - Mounts towards the left side
of the middle frame assembly |
|
RB3-0102-000CN |
Front inner cover (Blue) - Mounts on the front
frame above the multi-purpose input tray |
|
RB3-0103-000CN |
Front lower cover (blue plastic) - Front lower
strip below the multi-purpose input tray - Has recessed area for the
printer logo |
|
RB3-0104-000CN |
Roller cover - Covers the multipurpose paper
pickup roller assembly - Mounts on the lower front of the front
frame assembly |
|
RB3-0106-000CN |
Left side frame/cover (Quartz Gray) plastic -
Left side cover and input paper tray guide |
|
RB3-0109-000CN |
Front cover for the 250 sheet paper cassette
tray (Blue) plastic - Has molded in paper loading instructions and a
'2' on the front |
|
RB3-0120-000CN |
Solenoid cover (Steel) - For magnetic wave
sheilding |
|
RB3-0165-000CN |
Top inner cover (black plastic) - Covers the
back half of the pressure roller arms and springs - For the base on
the 250-sheet input tray assembly |
|
RB3-0166-000CN |
Bottom inner cover (Black) plastic - One covers
the paper feed sensor in the center and the other covers sensor
wires toward the right side - Mounts on the bottom of the center
frame assembly of the 250-sheet input tray assembly (two used) |
|
RB3-0282-000CN |
Inner cover - Covers the small interconnecting
PC board - Mounts on top of the right side support frame/cover
assemly on the base of the 250-sheet feeder assembly |
|
RB3-0283-000CN |
Inner cover - Covers the bottom of the
connector that interconnects the input tray base to the printer -
Mounts on the bottom of the right side support frame/cover assembly
for the base of the 250-sheet tray assembly |
|
RG5-6900-000CN |
Top cover assembly (blue plastic) - Includes
the molded-in face-down output tray and the lift-up top cover door
assembly |
|
RG5-6919-000CN |
Right side frame/cover assembly (Quartz Gray)
plastic - Includes the right side cover and paper tray guide, the
cassette retainer spring, tray 3 connector, printer interface
connector, and rubber feet |
|
RG5-6953-000CN |
Right side cover assembly (Quartz Gray) plastic
- Includes the DIMM memory door |
|
RG5-6902-000CN |
Left side cover assembly (Quartz Gray) plastic
- Includes the power switch button, rod and spring (The power switch
is located on the low voltage power supply board) |
|
RB3-0028-000CN |
Left side cover (Quartz Gray) - Does not
include any attaching parts |
|
Cross-Brace |
RB3-0108-000CN |
Metal support cross-brace - Mounts on the top
rear of the left and right support frame/cover assemblies - For the
base on the 250-sheet input tray assembly |
|
Damper |
RB2-6248-000CN |
Damper assembly (Gray plastic piece with small
13-tooth gear on it) - Helps to reduce clunking when the paper
pickup roller is engaged - Engages the paper pickup roller - Mounts
on the right side of the front frame assembly |
|
Door |
RB3-0033-000CN |
Memory access door (Quartz Gray perforated
plastic) - Allows access to the printer memory slots - Mounts on the
right side cover |
|
RF5-4007-000CN |
Top cover door (blue plastic) - For accessing
the toner cartridges and the imaging drum/transfer assembly - Mounts
to the top cover frame |
|
Drive Assembly |
RG5-6911-000CN |
Rotary drive assembly - Includes the carousel
rotating motor (DCM703), toner cartridge drive motor (PM705),
developing rotary stopper solenoid (SL93), bracket, and gears -
Rotates the toner cartridge carousel (DCM703) and provides drive for
toner operatio |
|
Drum |
C9704A |
Imaging drum/transfer assembly cartridge -
Inserts into printer through the top door - Life expectancy is
20,000 pages for black print only, 5,000 pages for color (Typical
combined life is approximately 6,000 to 8,000 pages) |
|
C9704-67901 |
Imaging drum/transfer assembly cartridge -
Inserts into printer through the top door - Life expectancy is
20,000 pages for black print ONLY, 5,000 pages for color (Typical
combined life is approximately 6,000 to 8,000 pages) |
|
Fan |
RH7-1537-000CN |
Cooling fan (Panaflo Model FBA08T24H - 80mm X
80mm X 15mm high, DC brushless, 24V DC, 190mA) - (FM712) Mounts in
the airflow guide/fan bracket assembly on the left side of the
printer |
|
Flag |
RB2-9925-000CN |
Sensor arm and flag - Activates the photosensor
(Does NOT include the roller) - For the Leading edge paper sensor
for the fusing assembly (PS720) - Protrudes up through the feed
plate on the middle frame assembly |
|
RB3-0111-000CN |
Paper flag - Plastic rod with paper sensing
flag on one end and sensor activator flag on the other - Senses
paper coming from the multi-purpose front input tray (tray 1) |
|
RB3-0130-000CN |
Shaft mounted sensor flag (black plastic) - For
the paper out sensor - Mounts on the paper pickup roller drive shaft
- For the base on the 250-sheet input tray assembly |
|
RB3-0132-000CN |
Mechanical sensor flag (black plastic) - For
the paper feed sensor - Mounts on top of the center frame assembly -
For the base on the 250-sheet input tray assembly |
|
RB3-0135-000CN |
Test print flag (Black lever) - Used to
activate the print engine test switch - Mounts in a metal holder in
the upper left of the front frame assembly |
|
Foot |
RB2-6297-000CN |
Rubber foot - Square self-adhesive rubber foot
- Attaches to the rear of the middle frame assembly (two used) |
|
Frame |
RB3-0105-020CN |
Center support frame (black plastic) - Support
structure for the paper pickup roller, feed roller, and paper
sensors - Mounts to the top front of both of the support frame/cover
assemblies on the base of the 250-sheet input tray assembly |
|
Fusing Assembly |
RG5-6903-000CN |
Fusing assembly (For 110V to 127V operation) -
Bonds the toner to the paper with heat - Slides in and locks in
lower rear of printer |
|
RG5-6913-000CN |
Fusing assembly (For 220V to 240V operation) -
Bonds the toner to the paper with heat - Slides in and locks in
lower rear of printer |
|
Gear |
RB3-0022-000CN |
22 tooth gear (Black plastic) - Small gear with
diagonally cut teeth - Idler gear between the transfer roller
assembly and the feed drive shaft - Mounts on the left side of the
middle frame assembly |
|
RB3-0091-000CN |
16 tooth gear (Black plastic) - Gear with large
stop tooth and shaft lock tab - Used as part of the mechanism to
disengage the drive cams for the imaging drum/transfer assembly -
Mounts on the inside of the right side metal chassis assembly |
|
RB3-0092-000CN |
15 tooth gear with drive shaft (Black plastic)
- Used as part of the mechanism to disengage the drive cams for the
imaging drum/transfer assembly - Mounts on the right side metal
chassis frame |
|
RS7-0418-000CN |
26 tooth gear (Black plastic) - Has 1/8th
portion of gear cut away - Mounts on the end of the paper pickup
roller for the multipurpose input tray (Tray 1) |
|
RS7-0424-000CN |
Dual gear - 20 tooth / 40 tooth - Mounts
between the right side of the front frame assembly and the paper
pickup gear plate assembly |
|
RS7-0425-000CN |
30 tooth gear (White plastic) - Part of the
drive gears for the registration roller - Mounts on inside of the
front frame assembly on the right side |
|
RS7-0426-000CN |
Dual gear - 26 tooth / 50 tooth (White plastic)
- Part of the drive gears for the registration roller - Mounts on
inside of the front frame assembly on the right side |
|
RS7-0428-000CN |
30 tooth gear (White plastic) - Mounts on the
end of the registration roller drive shaft |
|
RS7-0429-000CN |
26 tooth gear (White plastic) - Has recess for
shaft drive pin - Paper pickup clutch drive gear - Mounts between
the right side of the front fame assembly and the paper pickup gear
plate assembly |
|
RS7-0430-000CN |
26 tooth gear - White gear with 1/8th portion
of gear cut away and pin for spring tensioning - Mounts on the end
of the paper pickup roller in the base on the 250-sheet input tray
assembly |
|
RS7-0431-000CN |
15 tooth Gear (white plastic) - Mounts on the
end of the feed roller shaft in the base on the 250-sheet input tray
assembly |
|
RS7-0435-000CN |
Dual gear - 32 tooth / 37 tooth (White plastic)
- Drives the upper top bin output roller - Mounts on the right side
of the rear frame assembly |
|
RS7-0436-000CN |
Dual gear - 37 tooth / 43 tooth (White plastic)
- Part of the gear train for driving the upper top bin output roller
- Mounts on the right side of the rear frame assembly |
|
RS7-0437-000CN |
51 tooth gear (White plastic) - Main drive gear
for both the upper and lower top bin output rollers |
|
Gear Assembly |
RG5-6938-000CN |
Gear assembly - Metal plate with two White
plastic gears attached - Part of the drive gears for the paper
pickup roller for the multipurpose input tray (tray 1) - Mounts on
the right side of the front frame assembly |
|
Ground Plane |
RB2-9942-000CN |
Grounding plate - Provides grounding for the
top-of-page sensor and shielding for the density sensor boards -
Mounts on the top left of the front frame assembly |
|
RB3-0119-000CN |
Grounding plate - Grounds the paper pickup
solenoid cover to the right side metal chassis |
|
RB3-0137-000CN |
Grounding plate - Grounds the paper feed roller
- Mounts towards the right end of the center frame assembly - For
the base on the 250-sheet input tray assembly |
|
Guide |
RB2-9903-000CN |
Cable guide (Quartz Gray plastic) - Protects
and supports the upper cable assembly - Mounts to the right rear on
the laser/scanner support assembly |
|
RB2-9912-000CN |
Top output bin guide - Small curved ribbed
black plastic piece - Snaps on the rear of the printer just below
the upper top bin output roller (two used) |
|
RB2-9954-000CN |
Left paper feed guide (small Black plastic arm)
- Mounts to the left of the separation pad assembly on the lower
front frame assembly |
|
RB2-9955-000CN |
Right paper feed guide (small Black plastic
arm) - Mounts to the right of the separation pad assembly on the
lower front frame |
|
RF5-4049-000CN |
Entrance guide assembly - Angled metal guide
between the registration roller and the transfer roller - Mounts to
the bottom frame assembly |
|
RG5-6929-000CN |
Separation guide assembly - Includes the
plastic guide, label, and the two small spring loaded rollers -
Mounts in the fusing assembly |
|
RG5-6930-000CN |
Lower separation guide assembly - Includes the
guide bracket, paper output sensor (PS1) and flag, exit drive shaft
with two rubber rollers, shaft gear, and idler gear - Mounts in the
lower rear on the fusing assembly |
|
RG5-6935-020CN |
Left cartridge guide assembly - |
|
RG5-6951-000CN |
Paper guide assembly - Paper width adjustable
guide assembly for the multi-purpose front input tray (tray 1) -
Mounts with the two hinges on the lower portion of the front frame
assembly |
|
Hinge |
RB2-3041-000CN |
Tray hinge - For the left side of the
multi-purpose front input tray (tray one) |
|
RB2-3042-000CN |
Tray hinge - For the right side of the
multi-purpose front input tray (tray one) |
|
Holder |
RB2-9924-000CN |
Sensor assembly mounting holder - Holds the
leading edge paper sensor (PS720) for the fusing assembly - Mounts
on the underside left on the middle frame assembly |
|
RB3-0006-000CN |
Holder - Housing for the fusing connector
assembly - Mounts on the lower base pan of the printer mechanism |
|
RB3-0023-000CN |
Interlock switch holder (Quartz Gray plastic) -
Does NOT include the micro-switch - Mounts on the support shelf for
the laser/scanner assembly (just to the left of the laser/scanner
assembly) |
|
Hook |
RB1-2190-000CN |
Pickup roller spring hook - Clips on the pin of
the drive gear for the pickup roller and hooks the tensioning spring
- For the base on the 250-sheet input tray assembly |
|
Insulator |
RB3-0007-000CN |
Insulating sheet (Transparent plastic) - Mounts
between the bottom pan and the high and low voltage power supply
boards |
|
RB3-0056-000CN |
Insulating sheet (Transparent plastic) - Mounts
to the underside of the middle frame assembly |
|
Interface (Product) |
J3110A |
Ethernet 10Base-T (RJ-45) EIO network internal
print server PC board |
|
J3111A |
Ethernet 10Base-T/10Base2 and LocalTalk (RJ-45,
BNC, LocalTalk) EIO network PCA |
|
J4135A |
JetDirect connectivity card - Has one USB port,
one serial (DB9) port, and one LocalTalk port - Plugs in one of the
EIO slots on selected DesignJet and LaserJet printers |
|
J4167A |
JetDirect 610N token ring LAN interface board -
DB-9 and RJ-45 connectors |
|
J6057A |
HP JetDirect 615N internal print server LAN
interface board - 10Base-T and 100Base-TX - Plugs into peripheral
EIO slot, has RJ-45 connector - Includes software on CD-ROM and
manual |
|
J6057AR |
JetDirect 615N internal print server (10Base-T
and 100Base-TX) LAN interface board - Plugs into peripheral EIO slot
- Has a RJ-45 connector - Comes with software on CD-ROM and manual |
|
J6058A |
HP JetDirect 680N internal wireless
IEEE-802.11b (Wi-Fi) print server - Plugs into peripheral EIO slot |
|
Label |
RS6-8662-000CN |
Image cartridge label - Shows the imaging
drum/transfer assembly removal steps - Mounts on the right side of
the front inner cover (Visible when the top cover is lifted) |
|
Laser/Scanner |
RG5-6880-000CN |
Laser/scanner assembly - Mounts in the center
of the scanner support assembly |
|
Lever |
RB3-0178-000CN |
Right side lock release lever - Part of locking
system used to secure the fusing assembly in the printer |
|
RB3-0179-000CN |
Left side lock release lever - Part of locking
system used to secure the fusing assembly in the printer |
|
Manual |
5851-1468 |
LaserJet printer family paper specification
guide |
|
C9706-90926 |
HP Color LaserJet 2500 series service manual |
|
Memory (Product) |
C7845A |
32MB, 100-pin SDRAM DIMM memory module |
|
C7846A |
64MB SDRAM - 100MHz synchronous DRAM - DIMM
package |
|
C9121A |
128MB, 100-pin SDRAM DIMM memory module |
|
Motor |
RF5-4010-000CN |
Main motor assembly - Large motor mounted on a
controller PC board - Mounts on the inside of the metal right side
frame assembly |
|
RG5-6958-000CN |
Rotary motor assembly - (DCM703) Rotates the
four color toner cartridges in the carousel to position one of them
for printing |
|
RH7-1533-000CN |
Stepping motor - 24VDC - (PM704) swings (or
engages) the toner cartridge carousel in place to transfer toner -
Mounts on the left side of the rear frame assembly |
|
RH7-1535-000CN |
Stepping motor - 24VDC - (PM705) used to drive
the internal rollers and mechanisms in the toner cartridge when it
has been rotated in the printing position on the carousel |
|
PC Board |
C9145-69001 |
Formatter board assembly - Includes the
formatter board and all the metal cage covers - Mounts towards the
rear on the metal right frame assembly
REQUIRES RETURN OF DEFECTIVE PART(New part =
C9145-67901) |
|
C9705-69003 |
DC controller board - Mounts on the left side
of the printer (Behind the formatter board assembly)
REQUIRES RETURN OF DEFECTIVE PART(New part =
RG5-6959-060CN) |
|
RG5-6964-000CN |
Carousel position and toner level photoelectric
sensor PC board - 'L' Shaped PC board with the two sensors - (PS51)
Mounts on the left plate in the toner cartridge carousel assembly |
|
RG5-6968-000CN |
Interconnecting feed drive PC board - Mounts in
the right side cover assembly - For the base on the 250 sheet input
tray assembly |
|
WG8-5382-000CN |
Sensor PC board - Small board with flag
activated photosensor - (PS718) Paper sensor for the multipurpose
input tray, (PS720) front of page sensor for the fusing assembly,
and (PS716 and PS717) paper feed and paper out sensors in the 250
sheet input tray |
|
RG5-6965-000CN |
Waste toner sensor PC board - Small board with
an LED and photoelectric sensor - Monitors the level of the excess
toner deposited in the imaging drum/transfer assembly - Mounts on
the right side wall of the front frame assembly |
|
RG5-6967-000CN |
Registration sensor PC Board - Small board with
flag activated photosensor - (PS711) Mounts in the registration
assembly on the underside of the middle frame |
|
RG5-7612-000CN |
Top of page photoelectric sensor PC board -
Includes the photoelectric top of page sensor and the print engine
test switch - Mounts on the right side of the printer (Behind the
formatter board assembly) |
|
RH7-7146-000CN |
Density photoelectric sensor PC board - (PS81)
Mounts under the light blocking pad on the top of the front frame
assembly |
|
Pad |
RF5-4012-000CN |
Separation pad assembly - Includes the
separation pad, holder and spring - Mounts below the multipurpose
front input (Tray 1) pickup roller assembly |
|
RF5-4047-000CN |
Light blocking pad assembly - Black plastic
frame with soft rubber gasket and stiff conductive Mylar piece
(grounded) - Mounts to the top center of the front frame assembly |
|
RF5-4258-000CN |
Separation pad assembly - Includes the gray
plastic frame with the rubber insert strip - For the cassette on the
250-sheet input tray assembly |
|
Plate |
RB3-0010-030CN |
Feed plate - Center metal plate with slots that
the ribs on the middle frame assembly go through - |
|
RB3-0057-000CN |
Transfer slide plate - Small 'U' shaped metal
insert plates - Mount in the bushing wells for the transfer roller
on the middle frame assembly (two used) |
|
RB3-0065-000CN |
Contact plate - copper clad metal spring -
Holds the left end of the small 500 Meg-ohm resistor - Mounts on the
left side of the middle frame below the entrance guide assembly |
|
RB3-0066-000CN |
Contact plate - copper clad metal spring -
Holds the right end of the small 500 Meg-ohm resistor - Mounts on
the left side of the middle frame below the entrance guide assembly |
|
RB3-0286-000CN |
Contact plate - Runs between the shaft on the
registration roller and the metal entrance guide assembly |
|
Power Cord |
8120-6809 |
POWER CORD-UK |
|
8120-6810 |
Power cord (Flint Gray) - 2.3m (7.5ft) long -
Has straight (F) C13 receptacle (for 240V in Australia and New
Zealand) |
|
8120-6811 |
Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft)
long - Has straight (F) C13 receptacle (for 220V in Europe, Saudi
Arabia, South Africa, India, and Korea) |
|
8120-6812 |
Power cord (Flint Gray) - 18 AWG, 2.3m (7.5ft)
long - Has straight (F) receptacle (for 120V in the USA, Canada,
Mexico, Philippines, and Taiwan) |
|
8120-6813 |
POWER CORD (DOVE GRAY) - 2.3M (7.5FT) LONG -
HAS STRAIGHT (F) RECEPTACLE (FOR 240V IN THE UNITED KINGDOM, HONG
KONG, SINGAPORE, MALAYSIA) |
|
8120-6814 |
Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft)
long - Has straight (F) receptacle (for 220V in Denmark) |
|
8120-6815 |
Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft)
long - Has straight (F) receptacle (for 220V in Switzerland) |
|
Power Supply |
RG5-6960-000CN |
High voltage power supply board (HVT) assembly
- Has contacts for the eight high voltage springs in the printer -
Mounts in the bottom pan (Towards the front of the printer) |
|
RG5-7124-000CN |
Sub-high voltage board - Small auxillary PC
board - Mounts in a holder just above the high voltage board in the
bottom pan assembly |
|
RH3-2241-000CN |
Low voltage power supply - For 110V to 127V AC
operation - Includes the AC power input connector and power switch -
Mounts in the bottom pan towards the rear of the printer |
|
RH3-2243-000CN |
Low voltage power supply - For 220V to 240V AC
operation - Includes the AC power input connector and power switch -
Mounts in the bottom pan towards the rear of the printer |
|
Pressure Assembly |
RG5-6943-000CN |
Carousel pressure (support) assembly - Includes
the main rear support, E-label reader assembly, engaging sensor, and
the engaging rod shaft - Primary support structure for the toner
cartridge carousel |
|
Pulley |
RB3-0061-000CN |
Pulley roller (accommodates three feed belts) -
Small black roller approximately 3.49cm (1-3/4 inches) long with
three ball type pulleys - Mounts just behind the transfer roller in
the middle frame assembly (two used) |
|
RB3-0067-000CN |
Pulley roller (accommodates one feed belt) -
Small black roller approximately 1.59cm (5/8 inch) long with one
ball type pulley - Mounts just behind the transfer roller in the
middle frame assembly (two used) |
|
Rack Slide |
RB3-0090-000CN |
Rack slide - White plastic piece with gear
teeth layed out in rack form on both sides - Part of the mechanism
that disengages the imaging drum/transfer assembly cams when the top
cover is opened - Mounts vertically on the metal right side frame |
|
Reader |
RG5-6956-000CN |
E-label reader (contact board only) - Connects
the cartridge non-volitale memory to the DC controller board -
Mounts in the E-label reader assembly |
|
RG5-6957-000CN |
E-label reader assembly - Connects cartridge
non-volatile memory to the DC controller board - One for the imaging
drum/transfer assembly, the other for toner cartridges - One mounts
to the front frame assembly, the other to the toner cartridge
carousel as |
|
Rod |
RB3-0037-000CN |
Power switch rod - Goes between the power
button and the power switch on the low voltage power supply board -
Mounts on the left side cover |
|
Roller |
RB2-2892-000CN |
Guide roller (Free spinning white plastic
roller) - Mounts on the paper pickup drive shaft on each side of the
pickup 'D' shaped roller - For the base on the 250-sheet input tray
assembly |
|
RB2-7195-000CN |
Sensor flag roller (small White plastic roller)
- Mounts in the sensor arm flag for the leading edge paper sensor
for the fusing assembly (PS720) |
|
RB2-9908-000CN |
Pressure roller (small Black hard plastic disk
shaped roller) - Presses against the upper top bin output roller on
the top rear of the printer (two used) |
|
RB2-9909-000CN |
Pressure roller (small Black hard plastic
'solid' roller) - Presses against the lower top bin output roller on
the middle rear of the printer (two used) |
|
RB3-0012-000CN |
Belt roller - Small oval shaped roller
approximately 1-3/4 inches long - Mounts toward the center of the
metal feed plate on the middle frame assembly |
|
RB3-0160-000CN |
Paper pickup roller ('D' shaped) - Mounts on
the paper pickup roller assembly for the multipurpose front input
tray (tray 1) |
|
Roller Assembly |
RB3-0129-000CN |
Feed roller assembly - Includes the metal shaft
and two small rubber rollers - Feeds paper from the paper cassette
(or tray three below) into the printer - Mounts on the top of the
center frame in the base on the 250-sheet input tray assembly |
|
RB3-0161-000CN |
Paper pickup roller assembly - Includes the 'D'
shaped rubber roller on a plastic shaft - Mounts in the lower center
of the center frame assembly - For the base on the 250-sheet input
tray assembly |
|
RF5-4035-000CN |
Pressure roller and arm assembly - Includes the
small white roller, the holding arm, and roller scraper - Rolls
against the rubber feed rollers (two used) - For the base on the
250-sheet input tray assembly |
|
RF5-4040-020CN |
Transfer roller assembly - Long black foam type
roller - Transfers static charge to paper - Mounts towards the front
and on top of the middle frame assembly |
|
RG5-6897-020CN |
Upper top bin output roller assembly - Includes
the shaft with four rubber rollers, two bushing/shaft retainers, two
anti-reversing flaps, and the drive gear - Mounts on the top rear of
the printer |
|
RG5-6936-000CN |
Lower top bin output roller assembly - Includes
the shaft with four rubber rollers, two bushing/shaft retainers, and
the drive gear - Mounts in the center on the rear frame assembly
(above the fusing assembly) |
|
RG5-6939-020CN |
Registration roller assembly - Includes the
roller, bushings, mounting plate, paper sensor, and the sensor flag
- Mounts from the bottom toward the front center of the middle frame
assembly |
|
RG5-6952-000CN |
Paper pickup roller assembly - Includes the
shaft, guide assembly cams, the D-shaped roller, and roller
retainers - Picks paper from the multipurpose front input tray (tray
1) - Mounts in the lower portion of the front frame assembly |
|
Shaft |
RB2-4933-000CN |
Lock release shaft - Small shaft with locking
tab - Does NOT include the lock release lever - Used to secure the
fusing assembly in the printer (two used) |
|
RB3-0011-000CN |
Feed drive shaft - Long shaft with eight feed
belt ball type pulleys and one ribbed feed guide drive belt pulley -
Mounts behind the transfer roller on the middle frame assembly |
|
RB3-0060-020CN |
Idler gear shaft - Short metal rod - Shaft for
the transfer and feed drive idler roller - Mounts on the left side
of the middle frame assembly |
|
Shield |
RB2-9932-000CN |
RFI shield - Parallel wire form mounted over
the fan - Mounts on the fan air duct assembly on the left side of
the printer |
|
RB3-0136-020CN |
Solenoid cover/magnetic shield - Mounts on the
right end of the center frame assembly (over the pickup solenoid) -
For the base on the 250-sheet input tray assembly |
|
Shutter |
RG5-6940-050CN |
Registration shutter assembly - Includes the
metal roller, mounting frame, grounding springs, and the dual
coupling gear - Mounts over the registration roller at the front of
the middle frame assembly |
|
Sideplate |
RG5-6932-060CN |
Right side plate assembly - Includes the front
half of the metal frame assembly, gears, imaging drum/transfer
assembly drive cams, cover engaging mechanism, roller engaging
clutch (CL2), and main drive motor (DCM701) - Mounts on the right
side |
|
RG5-6934-000CN |
Right rear side plate assembly - Includes the
rear half of the metal right side plate, the fusing assembly drive
motor and the three associated gears - Mounts on rear half of right
side of printer |
|
RG5-6942-000CN |
Left side carousel plate assembly - End plate
under the rotational toner cartridge carousel - Includes all of the
high voltage contacts for the toner cartridges - Mounts on the metal
carousel support frame |
|
Solenoid |
RH7-5337-000CN |
Solenoid assembly - (SL92) Lever on the
solenoid disengages the stop on the drive gear on the paper pickup
roller for the multi-purpose input tray (tray 1) |
|
RH7-5340-000CN |
Solenoid assembly - (SL93) Engages to stop
rotation when the proper toner cartridge on the carousel is in place
for printing |
|
RH7-5341-000CN |
Solenoid assembly - (SL9) Lever on the solenoid
disengages the stop on the drive gear on the paper pickup roller -
For the base on the 250 sheet input tray assembly |
|
Spring |
RB2-2843-000CN |
Torsion spring - Provides a small amount of
back pressure for the paper sensor flag - For the base on the 250
sheet input tray assembly |
|
RB2-9905-000CN |
Torsion spring - Provides pressure for the
upper top bin output pressure rollers (two used) |
|
RB2-9906-000CN |
Torsion spring - Provides pressure for the
lower top bin output pressure rollers (two used) |
|
RB2-9952-000CN |
Tray 1 flag spring - Provides torsion for the
tray 1 paper sensor flag - Mounts in the lower portion of the front
frame assembly |
|
RB3-0015-000CN |
Compression spring - Provides upward pressure
for the left transfer roller bushing |
|
RB3-0016-000CN |
Electrical contact spring - Spring steel wire
with compression springs formed on both ends - One end provides
upward pressure on the right bushing for the transfer roller -
Connects to high voltage board |
|
RB3-0042-000CN |
Electrical contact spring - Mounts on the
middle frame assembly behind the transfer roller - Of the four
similar springs, this one is next to the one on the far left -
Connects to high voltage board |
|
RB3-0043-000CN |
Electrical contact spring - Mounts on the
middle frame assembly behind the transfer roller - Of the four
similar springs, this one is on the far right - Connects to high
voltage board |
|
RB3-0044-000CN |
Electrical contact spring - (Front) Provides
high voltage to the toner cartridge via a cable assembly and
connection through the carousel plate assembly - Connects to the
high voltage board |
|
RB3-0045-000CN |
Electrical contact spring - Rear electrical
contact spring - Provides high voltage to the toner cartridge via a
cable assembly and connection through the carousel plate assembly -
Connects to the high voltage board |
|
RB3-0046-000CN |
Electrical contact spring - Mounts on the
middle frame assembly behind the transfer roller - Of the four
similar springs, this one is just to the left of the one on the far
right - Connects to high voltage board |
|
RB3-0047-000CN |
Electrical contact spring - Mounts on the
underside of the middle frame assembly - Connects to high voltage
board |
|
RB3-0048-000CN |
Electrical contact spring - Mounts on the
middle frame assembly behind the transfer roller - Of the four
similar springs, this one is on the far left - Connects to the high
voltage board |
|
RB3-0121-000CN |
Right retaining spring - Helps to secure and
ground the imaging drum/transfer assembly in the printer - Mounts on
the upper right side of the front frame assembly |
|
RB3-0122-000CN |
Left retaining spring - Helps to secure the
imaging drum/transfer assembly in the printer - Mounts on the upper
left side of the front frame assembly |
|
RS6-2025-000CN |
Tensioning spring - Goes between the hook on
the pin on the paper pickup roller drive gear and a pin on the
center frame assembly - For the base on the 250-sheet input tray
assembly |
|
RS6-2030-000CN |
Tension spring - Provides support tension for
the multipurpose front input tray guide assembly (two used) |
|
RS6-2759-000CN |
Compression spring - Provides tension for the
power switch button - Mounts on the left side cover |
|
RS6-2760-000CN |
Compression spring - Provides pressure for the
pressure rollers on the center frame assembly (two used) - For the
base on the 250-sheet input tray assembly |
|
RS6-2766-000CN |
Tension spring - Provides a small amount of
return tension for the sensor flag arm on the leading edge sensor
for the fusing assembly (PS720) |
|
Static Dissipater |
RB3-0009-000CN |
Static eliminator ground plate - Right angled
metal piece with small teeth on top edge - Mounts from underneath on
the middle frame assembly just behind the pulley rollers |
|
Stop |
RB2-3019-000CN |
Shipping stopper (bright orange plastic) -
Helps to prevent damage to the paper tray by restricting the
movement of the lift plate (Removed for normal use) - For the paper
cassette on the 250-sheet input tray assembly |
|
Support |
RB2-9963-000CN |
Separation pad support - Pivoting 'L' shaped
metal support frame (Does NOT include the separation pad assembly) -
For the cassette on the 250 sheet input tray assembly |
|
RB3-0062-000CN |
PC board support (Black plastic holder) - For
mounting the small sub-high voltage board above the high voltage
board |
|
RG5-6907-030CN |
Laser/scanner support assembly (sheet metal
plate) - Crossmember between the two side frames - Support for the
laser/scanner assembly, the toner cartridge carousel drive motor,
and the cover interlock switch assembly |
|
Switch |
RH7-6051-000CN |
Microswitch with lever activator - (SW2) Senses
when the top cover is open - Mounts in a holder on the scanner
support assembly |
|
Thermistor |
RH7-7149-000CN |
Thermistor - (TH3) For detecting internal
temperature - Mounts to the metal right side frame assembly just
above the DC controller board |
|
Tray |
RB3-0019-000CN |
Toner catch tray (curved Black plastic piece) -
Holds residual toner from photosensitive drum - Mounts just below
the toner cartridge carousel on the bottom frame assembly |
|
RB3-0176-000CN |
Face-Up output tray door (ONLY) - Pull-down
tray door for face-up output - Mounts to the top of the locking
bracket on the fusing assembly |
|
RG5-6931-000CN |
Face-up output tray assembly - Includes the
pull-down door and fusing assembly locking bracket (Does NOT include
the lock releases) - Pull-down tray door for face-up output - Mounts
to the rear of the fusing assembly |
|
Tray Assembly |
C9699A |
Optional 500 sheet paper input tray - Includes
tray base which attaches to tray 2, and the slide out paper tray -
Accommodates 216mm x 279mm (8.5 x 11 inches) or 210mm x 279mm (8.3 x
11.7 inches) media - Optional 250 sheet tray must be installed first |
|
RG5-6914-040CN |
250 sheet paper tray assembly - Pull out
cassette that the paper is loaded into - Does NOT include the paper
feed base assembly - The cassette on the lower 250 sheet input tray
assembly |
|
RG5-6937-000CN |
Multi-purpose front input tray assembly
(tray-1) - Includes the front cover piece, pull-out paper support,
and the flip-out extender - Mounts on front of printer (on the front
frame assembly) |
